Did you install the Mach3 USB plug-in?

Make sure that you followed all of the steps and diagrams on the following page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
Absolutely nothing works. I have all structure and mechical parts of the blacktooth cutter done. However when i wire up the stepper motor to the motor driver. and that to the mach 3 usb controller board, and try to jog the motor, nothing works! I previosuly had the planet cnc breakout board, howrver, that only moved the motors in one direction and i couldnt change it. any help would be apreciated

Stepper motors are known to make noises while function, however this does not affect accuracy or job function. However we recommend to check your wiring for solid connections, and for good connectivity!



On a personal note, here is one cool video dealing with making songs with stepper motors!

Click the link to add information to this solution:
I bought and built the Blacktooth laser cutter. It works, but one of the stepper motors makes a loud static hiss a second after the CNC power supply is turned on or off, and makes loud tweets and twirps when running. It seems to operate fine otherwise. I was wondering if it was "going bad" or if that is normal?

I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

You should have no problem connecting the Pokeys57CNC controller to the drivers of your machine as long as the drivers have step (Pulse or PUL) and direction (DIR) terminals. You will need the cable pack that is sold separately so you can connect the headers/connectors of the pokeys57cnc controller to the drivers using ribbon cables.

I show this process in great detail on this page:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Is you scroll down on the page, you will see a set of videos that show the process step-by-step.

Click the link to add information to this solution:
I have a ShopBot CNC that was converted to Mach 3. The controller has gone out. I pourchased your Pokeys57 board, but I'm not sure I have everything I need. I think my motor drivers are OK, but am not sure how to wire them to what I purchased from you. Need Help. How can we make this work, or do I need a different board to distribute the movement signals to my drivers?

The drivers have quite a bit of protection, so you probably won't ruin anything. You motors are jumping and that is just the motors engaging from getting power from the power supply.

There could be many reasons your motors don't turn. Consider these troubleshooting tips:

- If you are using our parallel breakout board, make sure that the step pins are set for active low (config -> Ports and Pins -> Motor Outputs -> the steps pins should be enabled and set active low)

- The parallel breakout board is powered (connect the USB to the computer using a USB cable)

- In Mach3, make sure you have jog enabled (a little green button at thelower middle of the page in the program run screen).

Additional Information:


Additional Information:
DS26

Click the link to add information to this solution:
If I wired my stepper motors incorrectly what parts of the electronics will be ruined? When I turn on the power, my motors jump like they are supposed to but for some reason, the G-code doesn't seem to be moving from Mach 3 to the motors. Any help would be appreciated. Do I need to order new electronics or just part of the system? Thanks

The motor with that model number is here: https://buildyourcnc.com/item/electronicsAndMotors-nema24-425ozin

Click the link to add information to this solution:
In looking for a stepper motor amongst old parts in my lab, I found one with a sticker that says buildyourowncnc.com and PN SM60HT86-2008BF U2 on it. I found a Q&A on your website that says it's a NEMA 24 motor with 425 oz/in holding torque. I was wondering if you were able to confirm this? Any specs sheets and details of the motor would be much appreciated

The Mach3 USB will not work with Linux CNC. You can use our parallel breakout baord instead (if you have a computer that has a parallel port available).

Here is the link to that interface:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hello. I'm currently building my first CNC router, and I'm powering it with a 3 axis electronics kit that was purchased through your site. I chose to get the Mach 3 USB Breakout board, but now I'm wanting to try to use Linux CNC to work with the computer I have available. Will that work with this board?

The fact that you cannot move the motors with the keyboard serves as a clue to a couple possibilities.

- The software may not be communicating with parallel port. (One possibility may be that your step pins are not low active, or vice versa depending on your drivers).
- You may not be in the correct tab of Mach3. Make sure you are in the Program Run tab.
- The jog on/off button on the program run screen may not be lit (invoked).

This address below shows the complete troubleshooting for this type of situation. It will show how to test each pin at the parallel port at the back of the computer and everything else associated with correctly wiring the electronics.

https://buildyourcnc.com/CNCElectronicsandWiring.aspx




Additional Information:
6 axis robot with Mach3 Card 6 Axis Motion Controller

Click the link to add information to this solution:
I have a home built CNC running Mach 3. I have power to all the motors and the breakout board but no movement when running g-code. I cannot even manually move the motors with the arrow keys or page up and down. It also has an integrated 120v receptacle showing an open ground. I don't know if all this is related.

You want to look for the analog input terminals in the wiring diagram in the manual for your VFD. I believe the VFD you have, the XSY-AT1 has three terminals that will accept an analog voltage to adjust the speed. These terminals are:
COM or ACM - this is where the ACM from the controller will connect
VI/CI - The AVI will connect to this terminal which is the actual voltage level that will determine the speed from 0 to 10V.
10V - This connects to the 10V terminal of the controller which will provide 10V to the controller allowing the top voltage reference for the controller. This will provide a 0 to 10V range for the AVI or VI/CI terminals, and if 5V is available on the VFD, then the range will be 0 to 5V.

The parameter you need to change in the VFD is P10 which will change the source of the frequency, either the control panel which is the default (0 or 1, keys or potentiometer - dial, if that is available on the VFD), External analog signals which are the ACM, VI/CI and 10V/5V terminals in the VFD, or the RS485 which is a serial connection to the computer. You want to set this parameter to the External terminals which may be 2, but check your manual for the proper value.

Click the link to add information to this solution:
I'm hooking up the VFD Controller to the USB controller to control the speed of the spindle. In your video you have the wire from the USB controller to the ACM of the VFD controller. The VFD controller I have is a XSY-AT1 model AT1-2200s. It does not have an ACM contact. It does however have a SP1 contact, is this where I land that wire?

I am assuming that you are referring to the Mach3 USB controller.

Your understanding seems mostly correct, but it's important to clarify a few points regarding the 3D touch probe and the Mach3 USB Interface Board. The probe has three wires: 24V+, 24V-, and a signal wire. Here's how it typically works:

24V+ and 24V- Wires: These are for powering the probe. Make sure they are connected to the appropriate power supply.

Signal Wire: This wire sends the signal to the board when the probe is activated. In your case, it seems to be connected to pin 4.

Active Low Setting: If the probe is Normally Open (NO), when activated (i.e., when it touches the surface), it will complete the circuit. If you're using "active low NOT ticked," this means the board will interpret an open circuit (no contact) as an active signal. When the probe touches a surface and closes the circuit, the signal will stop.

It's crucial to ensure that the probe's voltage specifications match what the Mach3 USB Interface Board can handle. Since the board's inputs might not be designed for a 24V signal, using a voltage divider or an appropriate interface circuit to step down the voltage to a safe level for the board might be necessary.

Click the link to add information to this solution:
Hi. I have just purchared this board and will be using a 3d touch probe. The probe has 3 wires, 24v+, 24v- and a signal wire to the pin 4 (I think). The way I see it is that the probe is NO and the signal wire when activated will send a 24v+ signal to pin 4 (active low NOT ticked) activating the board. Would I be right in this understanding? Much apreciated.

The drivers have quite a bit of protection, so you probably won't ruin anything. You motors are jumping and that is just the motors engaging from getting power from the power supply.

There could be many reasons your motors don't turn. Consider these troubleshooting tips:

- If you are using our parallel breakout board, make sure that the step pins are set for active low (config -> Ports and Pins -> Motor Outputs -> the steps pins should be enabled and set active low)

- The parallel breakout board is powered (connect the USB to the computer using a USB cable)

- In Mach3, make sure you have jog enabled (a little green button at thelower middle of the page in the program run screen).

Additional Information:


Additional Information:
DS26

Click the link to add information to this solution:
My stepper motors stopped working all of a sudden. Mach 3 is running fine, just no signals getting to the motors. The lights on the motor drivers began blinking erratically when this started. Any advice where a problem like this can come from would be greatly appreciated.

If the sensors are NC (normally closed) you can wire them in series. If the sensors are NO (Normally Open) you can still wire them to the same input, but the wiring needs to be in parallel (like a ladder). I have more information on the following video:

Click the link to add information to this solution:
[788] Thanks for the oportunity to ask, I am building a cnc and using npn closed sensors could you help me with the conection of these, do i still connect them in series if i use more than two in each axis. Also you mention that a stop switch should be connected grd and input to the controller would that be done after the 24v power supply. Thanks r

can not get the limit switches to work on the usb controller board

Additional Information:
Wiring the motors to the drivers for our 8 wire motor is probably the 425 oz-in NEMA 24 stepping motor. Here is the URL for the diagram of the motor:
https://www.buildyourcnc.com/Documents/PN.SM60HT86-2008BF-U%20(inhouse%20PN.60BYGH303-13)%20(1).pdf

Wire it in bipolar parallel as specified on the data sheet.

Here is the URL for the motor to check if it is the same that you purchased.
https://www.buildyourcnc.com/item/electronicsAndMotors-nema24-425ozin

The USB mach3 board URL is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

The wiring diagram is on that page and instruction on how to use it.

Click the link to add information to this solution:
I recently purchased the 3 axis mach3 usb kit the motors have 8 different colored wires (no stripes on wire just solid color) all instructions have different colors. cannot find tutorals. does the mach 3 hook up same as planet? please let me know where I can find wiring diagram to hook up mach 3 usb BOB and motors (I am new to this kind of work projects)

Recommend first test to check a non-working axis, is to connect the current working axis(ex X-axis) to either the y/z axis to test the actual board and wiring in other axis setup. If tests failed and working (x-axis setup) does not working in the new axis location, go the Planet-CNC/File/Settings/Axes and check if your current non-working axis setup requires a inverted pulse. Check box and test again.
Next test if first fails, is to check continuity in your wires. A simple multimeter(ohm's) will work, just connect the positive and negative ends to one side of the same wire and if reading comes to 0.000, wire has continuity and if reads 0.L then there is a break in the wire and should be replaced.

Click the link to add information to this solution:
I installed the USB CNC Planet software- 2.10.1406.1201., and got out of your USB controller $ 75. 00.All have linked like a video USB CNC Controller/Interface Wiring Instructions Part 2, X - running . Y, and Z-axis does not work, it moves step motors and controller positions X -axis works, and Y and Z does not work.I used 425 oz-in motors

In all CNC electronics configurations, you will need the motor paired with its own driver.

If two motors/drivers are intended for a single axis and the motors need to turn at the same rate and in the same direction, then the two drivers for these motors should be connected to the same signal wires from the breakout board (step (CP) and direction (CW)) signal wires.

If the motors need to turn in opposite directions, then either one driver will need to have the direction signal inverted, or resolve the opposite direction through a change in the mechanical drive train (i.e. flip the rack on a rack and pinion configuration, or in a roller chain setup, have the chain ride along the opposite side of the drive sprocket).

How do I go about purchasing a redleaf system with 4 drivers, where the (y) and (a) driver are connected to the same signal from the breakout board? I'd also need them to rotate in opposite directions.

The redLeaf webpage contains a purchase option for an extra motor and driver. We can setup the redLeaf system uniquely so it conforms to your application (i.e. motors running in opposite directions).

Click the link to add information to this solution:
I've built a machine where the y axis has (2) 425oz motors, x axis has (1) 425oz. motor, and the z axis also has (1) 425oz motor. Would it be better to purchase a redleaf system with 4 drivers? or can I just connect both y axis motors to the same driver for a total of 3 drivers?

I also place the controller very close to the drivers (on the back of the gantry). All of the cables are shielded. The only long cables are the mains power cables and the USB cable. The USB cable is shielded and contains active repeaters.

There is no problem putting all of the electronics in a box and using long cables to the motors. This is the way I did it for a very long time.

Click the link to add information to this solution:
Great site. I saw your videos of wiring the Mach3 USB controller. You place the drivers next to the Steppers. This means that you have very long leads to the USB Board? What about the placement of the controlling PC? Is it a problem to have the USB board, PSUs and Drivers in a control box and long leads to the steppers? Thank you.

Not a problem. The ALM is rather self-explanatory as this is a closed-loop stepper motor and driver that you are using. The ALM (alarm) is a signal that is used to tell the driver/controller that the motor is not in the same condition that the driver expects. In a closed-loop system, the motor has an encoder that tells the driver exactly how many steps that it turned, and if this value does not coincide with the driver's outputted number of steps, and within a specified amount of time, the alarm will trigger so the system can stop and the workpiece can be salvaged.

The MF is simply a signal that tells the driver that there is impending direction and step pulses coming. If the MF signal is high, then that is similar to an enable signal.

Click the link to add information to this solution:
Hello I recently read your site and have a question. I have a driver model DM2722A but I can't connect it to my usb controller due to the fact that the driver is not marked enable, but instead it is marked: mf-, mf +, alm-, alm +. I will be very grateful if you explain to me the meaning of the latter and tell me what should be related to "enable" Thanks in advance!

We just received our new inventory of motors and that specific stepper motor ski came back with only one shaft. I’m not at the office to look at this inventory, so if that is true, they will all be single shaft. We may have other stepper motors with included rear shafts, but I will have to see on Monday.

If I don’t have the double shaft, we will provide a refund upon receipt of the motors. My apologies for this error.

Additional Information:
Hi, I'm sending these motors back today. As I understand you, you might have some motors from the previous lot still in stock, and these would be double shaft but otherwise you don't have any and won't be getting any. If you do have two double shaft versions of this motor please send them; if you don't have two of them please let me know--today if possible--so I can start looking elsewhere. Thanks, Ted Armen

Click the link to add information to this solution:
we just received two nema 11 stepper motors per our order--USR2-2, however they are single shaft, we need double shaft, I thought that's what we ordered. We're sending them back, let me know if you do have the double shaft version and I'll try again to order them. I notice the model number on the motor ends in "A", where the packing slip shows "B".

All of our controller will allow two steppers on any of the axes. Multiple stepper motors and drivers on a single axis is more a function of the way the stepper motor drives are connected to the output pins of the controller. To connect two stepper drivers to a single axis, you need to connect the output pins (dir and step) to each of the two stepper motor drivers.

Consider the controller on cost, features and how they are connected to the computer.

Out lowest cost controllers are:

Mach3 USB board - Has good features and uses the USB from the computer as the main connection
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout - The computer generates the main signals and this board conditions the signals for the drivers. Although it requires the parallel port from older computer, the board has the most broad compatibility with control software out there including Mach3 and LinuxCNC.
https://buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Highest cost but most feature rich:

Pokey57CNC - works with both Mach3 and Mach4
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
I am looking for a controller for a 3 axis dual Y stepper cnc machine. If at all possible I would like a list of the parts that will be needed. I prefer to go with an ethernet setup vs a parallel port.