When connecting the VFD to 220v, use the wiring diagram on this page to properly connect the wires from the 220v socket to the terminals of the VFD: https://buildyourcnc.com/item/spindle-inverter-2!2kw-spindle-novfd

Other than that, you will need a certified electrician to make sure that the wall socket is correctly wired to the fuse panel.

Click the link to add information to this solution:
Single Phase 220 supply to VFD. R=Neutral, S=110 Leg, T=110 Leg?? Not sure after reading up on this..

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. WHAT DO I NEED?

check your in-going power and make sure that you have a good neutral connection. Frequently the issue is not the power supply but the power coming into the power supply that causes the problem. There is a chance that the power is good coming in but there is a loose neutral connection and that causes it. This is the neutral connection that runs all the way back to the panel in your home.

Click the link to add information to this solution:
WHY DO MY 40W LASER POWER SUPPLIES KEEP FAILING?

Registration is recommended for a number of reasons. Many choose to register their works because they wish to have the facts of their copyright on the public record and have a certificate of registration. Registered works may be eligible for statutory damages and attorney's fees in successful litigation. Finally, if registration occurs within 5 years of publication, it is considered prima facie evidence in a court of law.

Click the link to add information to this solution:
WHY SHOULD I REGISTER MY WORK IF COPYRIGHT PROTECTION AUTOMATIC?

If there is play within the motor itself, then that motor may be defective. Call us to provide us more detail on this issue.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:
Ins9kru1

Additional Information:
-1 OR 2+486-486-1=0+0+0+1 --

Additional Information:
-1 OR 2+693-693-1=0+0+0+1

Additional Information:
-1' OR 2+890-890-1=0+0+0+1 --

Additional Information:
-1' OR 2+307-307-1=0+0+0+1 or 'HN9afNei'='

Additional Information:
-1" OR 2+88-88-1=0+0+0+1 --

Additional Information:
1'"

Additional Information:
1����%2527%2522

Additional Information:
@@mxOzC

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I have NEMA 34 motors for a GreenBull 6x12. After 2 weeks of use, my Y axis motor has developed play in the front but not rear of the motor. Is this a motor defect or has something come loose somewhere? Thanks,

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE MACHINE?

In Mach3, go to the Settings Tab, and select "Set Steps Per Unit". It will ask you how far to move the machine. Before you do this, make a mark on the table exactly where the end mill is resting. You can do this by lowering the end mill until it touches the material, then spinning it by hand to cut a small dimple in the material. Then, raise the end mill to clear the material, and assign a distance to move the machine. Once the machine moves and stops, measure the exact distance that it actually traveled with a tape measure, and enter this value into the dialog box that asks how far it moved. Mach3 will automatically adjust your steps per unit for that axis to be more accurate. Do this for all axes often to ensure you are cutting accurately. The longer distances you use calibrate, and the more precise you are with your measurements, the better.

Click the link to add information to this solution:
MY MACHINE NOT ACCURATE

A 1.5kW spindle will have ER11 (ER-11) collets. A 2.2kW spindle will use ER20 (ER-20) collets which can have bores for shanks up to 13mm or 1/2".

Both spindles typically have an 80mm body diameter. 2.2kW can have a larger diameter from some manufacturers.

Click the link to add information to this solution:
how to identify spindle? 1.5 or 2.2 my spindle has er20 collets,220 colt. black vfd

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

Vaccines can be administered at any time before or after administration of an "allergy injection."

Click the link to add information to this solution:
WHAT THE RECOMMENDED INTERVAL FOR RECEIVING INFLUENZA VACCINE AFTER AN ALLERGY INJECTION?

Yes, we accept standard credit cards on our shopping cart. All you need to do is enter the credit card information in the payment area.

Click the link to add information to this solution:
DO NOT HAVE PAYPAL ACCOUNT, WITH NO DESIRE TO OBTAIN ONE.

Make sure to watch my Mach3 USB outputs video on the product page for the Mach3 USB controller. If it still doesn't work, make sure to set the port to port 3 for the output you are using.

Click the link to add information to this solution:
mach 3 not activating output 1?

The PlasmaSense THC has two terminals for high-voltage inputs + and - at a max of 350V and alternative terminals for +10 and -10 volts max intended for the divided voltage from the plasma cutter.

If the divided voltage does not exceed 10V + or -, then you can use this THC. If the divided voltage is more than 10V, you will need to further reduce that divided voltage.

Click the link to add information to this solution:
[803] my plasma cutter has a 50 to 1 divided voltage what can i do to wire that to the thc? let me know thanks.

Asia has the biggest population.

Click the link to add information to this solution:
WHICH CONTINENT HAS THE BIGGEST POPULATION?

Russia has the biggest land area.

Click the link to add information to this solution:
WHICH COUNTRY HAS THE BIGGEST LAND AREA?

Not a problem. We will make sure to adjust your order.

Click the link to add information to this solution:
Hi. i have a mistake in my order this morning and wish to order 3-#25 (3(/8 id) sprokets and NOT #35S

Dealing with our 3/8" ACME screw, we intended to use this with a 3D printer machine(primarily) as well as our smaller motors. Which did not need the increased torque ratings as our larger motors, which will use the 1/2" ACME screw with larger machines.

Click the link to add information to this solution:
Why is your 3/8" acme thread only 2 start and your 1/2" is 5 start?

Flip the values under "table travel" within "stepconf wizard". For example: if the table travel numbers are "4 to -10", switch them to "-4 to 10".

Click the link to add information to this solution:
MY AXIS ONLY MOVES ONE STEP AT A TIME IN LINUX CNC EMC2

Yes, the customer will need to sign our NDA (Non Disclosure Agreement) form and send it back to us. We will then send the dxf of the specific updated part of the machine.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:
UoZD5KPp

Additional Information:
-1 OR 2+416-416-1=0+0+0+1 --

Additional Information:
-1 OR 2+291-291-1=0+0+0+1

Additional Information:
-1' OR 2+657-657-1=0+0+0+1 --

Additional Information:
-1' OR 2+849-849-1=0+0+0+1 or 'WBwHf8k5'='

Additional Information:
-1" OR 2+276-276-1=0+0+0+1 --

Additional Information:
1'"

Additional Information:
1����%2527%2522

Additional Information:
@@z69Jq

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
CAN I GET DXF FILES FOR THE UPDATED PARTS OF MY MACHINE?