The Mach3 USB controller will work with M3/M4/M5 or M7/M8/M9 combinations. M10/M11 is not available with the controller.

Click the link to add information to this solution:
[575] does the mach3 usb interface board support the M11/M10 command set?

In our experience, the backlash compensation is not an ideal mechanism to solve backlash issues. It is best to resolve the backlash issue mechanically regather than through software.

Boards that handle all instructions on its own chip (which is the case for this all other USB boards) take some control away from Mach3. Without Mach3 having granular control. With that said, we do not have experience with the backlash compensation with that particular board. Our experience with backlash compensation with other boards have resulted in very poor accuracy and undesirable geometrical moves.

Additional Information:
zokkj

Additional Information:
zokkj

Additional Information:
zokkj

Additional Information:

Click the link to add information to this solution:
Mach3 USB Interface Board, Backlash Compensation in Mach3 is not working. Does this board support the backlash function?

Planet-CNC is the control software. If you decide to use the USB controller, you will need to use the planet-CNC software as the control software. You will be able to use any of the CAM software applications with the planet-CNC control software.

Click the link to add information to this solution:
Would I be able to use the Mach3 CNC Control Software or any of the CNC CAM Software(BOBCAD/CAM,CAMBAM) if I choose to use the Planet-CNC USB Interface Board?

The Mach3 USB board will fit in the redLeaf, but you may need to modify the Plexiglas top for proper mounting. However, the redLeaf has the proper parallel GPIO on the motherboard for use with the Parallel breakout board. If you have a laser on the machine you are using, then I would urge you to maintain the parallel breakout board as the Mach3 USB board will not work correctly using the Z-direction pin and you will need to determine how to use the output pins onthe USB board to ensure proper laser functionality.

Click the link to add information to this solution:
Will Mach3 USB Interface board fit in my redleaf, in lieu of the breakout board that came with it?

The usb controller will only work with the planet-cnc software which is software that will work in Windows.

Click the link to add information to this solution:
Does USB Controller Breakout support Linux Ubuntu and does the software support command line interface (to control it with python scripts for example)

The usb controller will only work with the planet-cnc software which is software that will work in Windows.

Click the link to add information to this solution:
Does USB Controller Breakout support Linux Ubuntu and does the software support command line interface (to control it with python scripts for example)

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I AM INTERESTED IN THE 3 AXIS COMBO USB OPTION. NOTICE YOU ENDORSE PLANET-CNC FOR USE WITH THIS BUT WILL MACH3 INTERFACE WELL BEAK OUT BOARD?

I do not recommend using the Mach3 USB controller to be used with a torch height controller. There are only 4 inputs on the Mach3 USB controller. We have tried to interface a Proma THC to this board without success; however, we did not exhaust all possibilities.

I would recommend the Pokeys57CNC controller to connect the Proma THC as I have interfaced these two before and they work well together.
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[575] Hello. Does this USB interface board thc? I have the proma 150.

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I am interested in the 3 axis combo USB option. I notice you endorse the Planet-CNC for use with this but will Mach3 interface well with the USB beak out Board?

You have the ability to designate the 4th axis, commonly known as the A-axis, for rotary indexing operations when using a Mach3 USB controller.

To achieve this in Mach3, you'll need to:

Open the Mach3 software.
Navigate to "Config" and then to "Ports and Pins."
Go to the "Motor Outputs" tab.
Enable the A-axis and assign the respective Step and Direction pins.
Save your settings and exit the "Ports and Pins" dialog.
To calibrate the A-axis, go to "Settings" and use the "Set Steps Per Unit" option.

Click the link to add information to this solution:
[575] Does this board support indexing on mach3 turn? Planning to use it on a lathe and will do threading jobs

Depending on the probe that you have, you should have two wires coming from the probe. One of those two wires will need to be connect to an input pin as shown in this wiring diagram (the diagram show the probe connected to pin I4):
https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf

The other pin is connected to V-. Please make sure that you have 24V connected to the V- and V+ on that side of the Mach3 USB board.

The way the probe works is when the probe is in contact with an object, a specific spring mechanism will cause the input pin to be connected to the V- (close the circuit). When Mach3 senses an active low on the input pin, mach3 knows that the probe has made contact (closed the circuit).

If your probe is used as a Z-Axis zero plate, then the concept is the same, but the end mill is connected to V- and the plate is connected to the input pin. If the plate comes in contact to the end mill, then the circuit is closed and mach3 will sense an active low on the input pin.

Click the link to add information to this solution:
Mach3 USB interface board. Could you please give me the correct wiring configuration for tool prob?

The Mach3 100 kHz controller may be able to support the Sherline 1/2 pulse mode, but I have not tried it. There is no information in the documentation that is related to the parameter that can be set in Mach3 for the Sherline 1/2 pulse mode. You may be able to play with the available kHz ranges that the plugin allows to see if there is a pulse width that meets the Sherline 1/2 pulse mode specification.

Click the link to add information to this solution:
[575] Does the USB MACH3 controller support Sherline 1/2 pulse mode?

Planet-CNC is the control software. If you decide to use the USB controller, you will need to use the planet-CNC software as the control software. You will be able to use any of the CAM software applications with the planet-CNC control software.

Click the link to add information to this solution:
Can I use your USB interface board and Mach3 on my 3 axis CNC router?

You can find instructions for the Mach3 USB here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

You will probably need to use the Mach3 USB board with Mach3. We have not tested the Mach3 usb card with Mach4.

Click the link to add information to this solution:
Whereb can I find directions on how to install the Mach3 USB board with Mach 4 software? I do not have a parallell port.

Yes, you can use a laptop if you have a controller that uses a USB, like the Mach3 USB card. If you don't have that, you can purchase that part here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

If you have a controller board that connects to a 25 pin connector, modern laptops will not be able to connect to that port.

How old is your CNC computer system?

Additional Information:
The CNC computer system is 2013 (5 years). The built in video card went out. I will order the Mach3 USB card. Thank you.

Additional Information:
You're welcome

Click the link to add information to this solution:
The motherboard on the computer I bought from you went out. What would you suggest. I have a laptop, could I use it and use a Mach3 USB interface board?

Yes, the Mach3 USB controller will work with the latest Windows version and in 64-bit mode. The 32-bit mode is only relevant for using the parallel port driver if you are using a parallel port breakout board. Since this controller is connected via a USB cable, the 64-bit state will work fine.

Click the link to add information to this solution:
[575] I have a 64 bit Windows 11 laptop. Will this interface board work with this? If not is there an option you can suggest.

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

Planet-CNC is the control software. If you decide to use the USB controller, you will need to use the planet-CNC software as the control software. You will be able to use any of the CAM software applications with the planet-CNC control software.

Click the link to add information to this solution:
I want to use Planet-CNC software can I use Mach3 USB Board

The dimensions for our USB breakout board are:

L: 2.745"/ 69.723mm
W: 2.244"/ 56.9976mm
H: .501"/ 12.7254mm

Currently we do not have a CAD model on hand.

Click the link to add information to this solution:
What are the overall dimensions of the USB interface board? Is there a CAD model available?