Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I AM INTERESTED IN THE 3 AXIS COMBO USB OPTION. NOTICE YOU ENDORSE PLANET-CNC FOR USE WITH THIS BUT WILL MACH3 INTERFACE WELL BEAK OUT BOARD?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I am interested in the 3 axis combo USB option. I notice you endorse the Planet-CNC for use with this but will Mach3 interface well with the USB beak out Board?

I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

Click the link to add information to this solution:
if I wanted to use your inductive proximity sensor's with your USB interface board what would I need besides the sensors I would be using 5 of the sensors.

Yes, you can use a laptop if you have a controller that uses a USB, like the Mach3 USB card. If you don't have that, you can purchase that part here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

If you have a controller board that connects to a 25 pin connector, modern laptops will not be able to connect to that port.

How old is your CNC computer system?

Additional Information:
The CNC computer system is 2013 (5 years). The built in video card went out. I will order the Mach3 USB card. Thank you.

Additional Information:
You're welcome

Click the link to add information to this solution:
The motherboard on the computer I bought from you went out. What would you suggest. I have a laptop, could I use it and use a Mach3 USB interface board?

Mach3 is not compatible with the USB breakout board, so you need Planet CNC in its place.

Additional Information:

I am confused by this same issue. I am using the Mach3 USB interface board with Mach3 and it works fine. In fact a video of it is on this very website. (link below)

Is the Mach3 USB interface board the same thing as Planet-CNC USB board?
It has been stated on this FAQ that it cannot be used with Mach3 and can only be used with Planet CNC USB software.

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
In a Windows configuration, Using the USB breakout board, is the Planet-CNC software used in conjunction with Mach3 or in place of it?

I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

Click the link to add information to this solution:
Good evening, if I wanted to use your inductive proximity sensor's with your USB interface board what would I need besides the sensors I would be using 5 of the sensors. I have a 48V 12amp power supply. Thank you

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

Planet-CNC is the control software. If you decide to use the USB controller, you will need to use the planet-CNC software as the control software. You will be able to use any of the CAM software applications with the planet-CNC control software.

Click the link to add information to this solution:
I want to use Planet-CNC software can I use Mach3 USB Board

You can download a trial version of PlanetCNC software from their site at http://www.planet-cnc.com/index.php?page=software to see how you like the interface. If you look at their main GUI screen, along the left side you will see 4 boxes labeled X,Y,Z and A. These represent the axes the software is equipped to control. (A being Axial, or rotational motion) Typically a separate motor and driver is used to control each axis. If you plan to switch axes you will need to connect and disconnect the outputs from your software to the drivers.

Click the link to add information to this solution:
sorry, this is what i meant to say: OK, so if I use the USB version then I would find the rotary/linear axis definitions in the planet cnc control software somewhere. I will be needing to change axis type often for various projects that is why I am asking.

The Mach3 USB controller only works with Mach3. We have a controller that works with Mach3 and Mach4 called pokeys57CNC controller.
Here is a link to that controller:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
Hi Do you know if your Mach3 interface board works with any of other of the current CAM programs such as MACH4?

The Mach3 USB controller only works with Mach3. We have a controller that works with Mach3 and Mach4 called pokeys57CNC controller.
Here is a link to that controller:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
Hi Do you know if your Mach3 interface board works with any of other of the current CAM programs such as MACH4?

Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

Some of the types of CNC electronics we will consider.

- We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

- We will repair or retrofit used CNC electronics.

- Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

Here is an example of CNC electronics that we worked on for a customer:

Click the link to add information to this solution:
I would like to use Mach3 instead of the software for my CNC router. Can you fix the electronics for me?

The USB interfaces (The board shown at the link: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout) that we well is already updated with the firmware, and tested with the planet-cnc software. Simply install the planet-cnc software and plug in the USB interface and the software will communicate with the board.

Additional Information:
Windows 10 was not allowing the planet cnc software to install the proper drivers. Following the windows 8 reccomendations listed on the usb break out board page got the planet cnc and usb break out board communicating.

Click the link to add information to this solution:
How do i get the USB break out board to communicate with the exceptional Planet-CNC USB software?

Ok. Email me at customerservice@buildyourcnc.com to setup the return.

Thanks.

Click the link to add information to this solution:
I would like to return the Mach3 USB CNC Interface I just received. I am not continuing the project requiring it.

The Mach3 USB controller is specifically engineered to integrate seamlessly with Mach3's CNC control software. Easel, on the other hand, offers an all-in-one CAD/CAM solution along with machine control capabilities. While Easel can output standard G-code compatible with industry-standard post-processors, it can serve as a design tool when used in conjunction with Mach3 but not as the machine control software.

Click the link to add information to this solution:
[575] Will the Mach3 USB interface board support other software such as Easel?

Generally, you’ll need to check what control software will need to be used with the CNC router. Our machines use industry standard electronics and control software that is nonproprietary so you can use just about any software out there with our machines.

Specifically, what software are you planning on using?

Additional Information:
dear Sir,
I'm searching for the best one,I think that I have to learn more about that in order to be able to make the right decision.

Additional Information:
If you are using a computer running Microsoft Windows, then I would recommend using Mach3 or Mach4. If you prefer Linux, then LinuxCNC is the best control software in my opinion.

Click the link to add information to this solution:
I'm searching for a desktop cnc, could you tell me please if any software I may choose could be compatible with all desktop cnc machine or I have to check the compatibility before ?

Do you have any intention to upgrade to Mach4? If you will be staying with Mach3 for a while, then the Mach3 USB interface is fine. If you intend to change to Mach4, then I would go with the Pokeys57CNC interface.

Click the link to add information to this solution:
Hi Patrick right now I have a parallel port cnc machine that I built in 2013. I want to update my system to use a usb. Do you recommend changing my interface board to a Mach3 USB interface board or purchasing the UC 100 parallel port to USB adapter?

The usb controller will only work with the planet-cnc software which is software that will work in Windows.

Click the link to add information to this solution:
Does USB Controller Breakout support Linux Ubuntu and does the software support command line interface (to control it with python scripts for example)

The usb controller will only work with the planet-cnc software which is software that will work in Windows.

Click the link to add information to this solution:
Does USB Controller Breakout support Linux Ubuntu and does the software support command line interface (to control it with python scripts for example)