if you purchased the USB interface, you will need planet-cnc software rather than Mach3, and you will need a usb cable to connect the usb interface to the computer.

The blackToe 2x4 CNC Machine Kit with optional table will need wire to connect the electronics. Don't forget to get some end mills to use for cutting the intended material.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
If I purchase the [blackToe 2x4 v4.1 CNC Machine Kit - USB Electronics - Table Included] all I would need for this CNC to be fully operational is a laptop with mach 3 software and a router. Is this correct?

We do offer all of the parts; but it is best to purchase them a la carte. You will probably not want the hardware since this would not conform to a design in metal.

All of the mechanical parts are available here:
https://buildyourcnc.com/CNCMachineMechanicalParts.aspx

All of the electronics you would need is available here:
https://buildyourcnc.com/electronicscombo.aspx

All of the laser components are available here:
https://buildyourcnc.com/LaserComponents.aspx

And the spindles and VFDs are available here:
https://buildyourcnc.com/SpindlesAndAccessories.aspx

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Is it possible to order the mechanics, motors and electronics, in other words, order the kit without the wood? Reason being is I have aluminum and steel to make a machine out of.

If you are wanting to purchase all of the parts for a machine excluding the structural parts, you will need to order the parts a la carte.

Electronics packages can be found here:
https://buildyourcnc.com/category/elcombo

Mechanical components can be found here:
https://buildyourcnc.com/CNCMachineMechanicalParts.aspx

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Is it possible to order the mechanics, motors and electronics, in other words, order the kit without the wood? Reason being is I have aluminum and steel to make a machine out of.

The motor is helped by the mechanical leverage of the screw. The 425 oz-in motors that are included in the standard electronics combo has very high torque for that type of machine. You will have no problem using that motor for the book machine.

We use that motor for very heavy spindles on the blackToe and blackFoot CNC Machine kits.

You will need to do the mechanical leverage calculation along with the torque of the motor to determine the actual weight it will lift. The calculation will need to consider the type and pitch of the screw and it would also consider the gravity constant of 9.8 m/s/s.

If you need me to determine this formula and work out the calculation based on the screw you are using, please let me know.

Additional Information:
thank you for the reply. I would be really good to know the calculation. The lead screw is 1/2" diameter with 13 TPI. Please provide the calculation. And one more question. If I am cutting 18mm MDF with 6mm cutting bit (so 6mm pass), what can be the maximum speed rate of cutting and spindle speed of router?
thank you

Click the link to add information to this solution:
I received the electronics for book build cnc machine. I need to know how much weight the z-axis motor can hold since my (craftsman) router seems to be heavy. It is 2HP with variable speed

Attaching two motors in parallel is possible, but you will need another motor and driver for the opposite side. Each motor must have its own driver to work accordingly and fluently. The two can be wired together, to the same pins on your breakout board and set the dip switches on the driver to match the ones on your x-axis(ex). But remember to view the orientation of the motor and which way it spins, since it is on the opposite side it will have to be orientated correctly to move in sync with the other motor.

Click the link to add information to this solution:
I just finished building my first CNC with the electronics I purchased from you and I am already thinking about improving it. I would like to build a 2 motor X axis solution. Is it possible to attach 2 parallel motors and drivers to the BlueBrew Breakout Board? If so, how?

You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

Use a clamping collar (if you are using an ACME lead screw) or a couple of 1/2 nuts (if using an allthread) against the bearing to keep the bearing in place and make sure there is no axial play.

Click the link to add information to this solution:
How do I secure the non-motor end of the lead screw for my 'Book' machine build? Does it just sit inside the bearing or do i use a nut to lock it in place? I did not see any instructions for this in the book.

Considering enlarging the machine, might have its down sides do to the structural integrity of the scratch build machine. Primarily by making the width longer it will start to sag in the center, which will lead to having to redesign the gantry to be more structurally rigid to support the added length. Which then will increase the weight and height of your gantry to support the add size, which will always end up to creating a larger CNC.

We usually do not recommend modifying the scratch build CNC, due to the very limited capabilities, and the structural design of the scratch build. We also do not recommend using longer than 48" ACME screw/leadscrew due to the increasing chance of warping and bending in the ACME screws/leadscrew in the given length.
We do recommend modifying the CNC machines we sell to accommodate the added requests that some of our customers desire, but you will be limited to the width of the gantry with our machines.

Click the link to add information to this solution:
I've read your book and I'm looking to purchase the hardware kit with DVD as well as an electronics kit. I would like my machine to have a working area of at least 24" wide by 48" long. Can I just make the bed (and gantry) wider to accommodate larger priceslike 30"x60"? If so what electronics kit would you recommend?

We recommend our electronics combo for the scratch build kit, which you can find on our site here: https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo. This is our standard general purpose 3 axis electronics system, and includes (3) NEMA 24 425 oz-in stepping motors, (3) Drivers (3.0Amp 24-40 Volts, with 1-1/64 microstepping), (1) 36v 8.8a Power Supply, (1) Interface Board either USB or Parallel. (The USB version requires PlanetCNC software; the parallel interface board gives you a variety of options, Mach3 being one popular choice.)

Click the link to add information to this solution:
I am going to build a CNC 4x4 plasma table. The frame is made of 1 1/4" pipe and the gantry will be made of either 2"x 2" or 2"x 3" tubing. What size stepper motors do you suggest?

Yes, we offer a CNC electronics assembled package called the redFly, redLead and redSprout. If you already have a computer, I would recommend the redFly. You would still need to add connectors to the ends of your motor cable.

https://www.buildyourcnc.com/item/cnc-computer-system-redFly

Click the link to add information to this solution:
I need to replace the fried electronics box for my 6090 wood router. Do you offer a play and play, no wiring required, kit? If yes, how much? If no, can you recommend one?

We recommend our electronics combo for the scratch build kit, which you can find on our site here: https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo. This is our standard general purpose 3 axis electronics system, and includes (3) NEMA 24 425 oz-in stepping motors, (3) Drivers (3.0Amp 24-40 Volts, with 1-1/64 microstepping), (1) 36v 8.8a Power Supply, (1) Interface Board either USB or Parallel. (The USB version requires PlanetCNC software; the parallel interface board gives you a variety of options, Mach3 being one popular choice.)

Click the link to add information to this solution:
I got the plans and hardware from you guys and im almost ready for the stepper motor part of this build. what size motors are good to use for this build? the size of cnc will be 2x4 when finish or what size will not work? thanks

We do offer all of the parts; but it is best to purchase them a la carte. You will probably not want the hardware since this would not conform to a design in metal.

All of the mechanical parts are available here:
https://buildyourcnc.com/CNCMachineMechanicalParts.aspx

All of the electronics you would need is available here:
https://buildyourcnc.com/electronicscombo.aspx

All of the laser components are available here:
https://buildyourcnc.com/LaserComponents.aspx

And the spindles and VFDs are available here:
https://buildyourcnc.com/SpindlesAndAccessories.aspx

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hello, I'm interested in GreenBull 5'x10' CNC machine kit with 40W laser head. Is it possible to receive an offer for this size cnc machine kit with all the mechanics, electronics and laser parts, but without all the wooden parts? We would like to build this kind of laser cutter machine with metal frame and parts. And is it possible also to get 3D drawing for machine? Waiting for your answer.

Sure, email me at customerservice@buildyourcnc.com and I will send you a replacement for a minimal fee. I now use HDPE for that part. The HDPE holds up much better.

Click the link to add information to this solution:
I have a Blackfoot 4x4 v2 chain drive. my Y plate is broken . do you sell just the Y plate or can I buy just the Y plate spec plan? I love this machine Its great. my name is Jeff Krug I bought the complete package and electronics from you guys. thanks

Book build (scratch build), feedrates and recommendation.

Using standard allthread will provide around 20-30 ipm using 36 volts. Although it allows for a working CNC machine, the RPM of the spindle/router will need to spin at the lowest setting to provide the beat efficiency and life for the end mill at 1/4" cut diameter and higher. The speeds may be fine for smaller end mills.

If you would like faster speeds, you should change the lead screws on the CNC machine to the 1/2" 5 start 10 TPI which translates to 2 turns per inch which means, the stepping motor will not need to turn as fast to produce faster motion. That is to say, the stepping motor will only need to turn two revolutions for the machine to travel one inch and with the allthread, the stepping motor will need to turn 13 times to reach one inch.

Link to the lead screw and other mechanical parts needed:
https://www.buildyourcnc.com/CNCMachineMechanicalParts.aspx

To change the lead screws you will need (for each axis):

1. The lead screw for that axis.
2. Two 1/2" collars to keep the lead screw axially stable.
3. One Antibacklash nut.

Additional Information:
20

Click the link to add information to this solution:
Since I am using normal all-thread lead screw 13 TPI 1/2" for the book build cnc, what can be the maximum feed rate of machine and how can I change the mechanical setup in mach 3? I am using 1/4" steel carbile endmill with 2 flutes and router is 2 HP with variable speed

The blackToe 2'x4' cnc machine is sold as a kit only. We offer plans for the scratch (book) build machine that can be found here for purchase and also comes with a DVD showing the build process: http://www.buildyourcnc.com/cnckitintro.aspx and the plans for build in the book is on the CNC book page: http://www.buildyourcnc.com/Book.aspx.

You can use the same size stepping motors referenced in the book: http://www.buildyourcnc.com/category/elcombo

Click the link to add information to this solution:
I would like to build the 2’x 4’ blackToe2x4v40 CNC router. I have your book. I want to build the latest model blackToe2x4 v40. Are those the correct plans on your web book page ? Is there a bill of materials? If I use a Porter Cable 3-3/4 router motor what size stepper motors do I need?

Please contact sales@buildyourcnc.com for a custom quote.

Click the link to add information to this solution:
I want to build a 4 x 4 plasma table. I am not good with the electronic parts of the system. What would you recommend as a turn key electronics package? I also want to build it with chain drive

What is the weight of the gantry, number of teeth on the drive sprocket and tooth pitch?

Click the link to add information to this solution:
I build a 3 axis router CNC the gantry is heavy in aluminium plate, witch plug n'play kit you suggest me 1 or two motor on the longest axis this will be drive with chain?

Yes, the redLeaf plug-and-play CNC electronics can include a THC (Torch Height Controller) and motors of any size. The limit of the number of motors that this package can include is 8 motors in total.

Click the link to add information to this solution:
Will the redleaf package allow me to run a torch height controller and 2 nema 34 motors for my gantry? I would prefer to have motors on both sides of the machine with a heavy gantry

Do you have any intention to upgrade to Mach4? If you will be staying with Mach3 for a while, then the Mach3 USB interface is fine. If you intend to change to Mach4, then I would go with the Pokeys57CNC interface.

Click the link to add information to this solution:
Hi Patrick right now I have a parallel port cnc machine that I built in 2013. I want to update my system to use a usb. Do you recommend changing my interface board to a Mach3 USB interface board or purchasing the UC 100 parallel port to USB adapter?