Hi. The relay that we sell here:
https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Has the same relay as the parallel breakout board:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

And contains three terminals: "S", "P" and "P". The "P" is always connected and will be the connection between the "S" or the "O" depending on if you need the connection to be Normally Closed (NC) or Normally Open (NO).

- Use the "O" if you need the connection from "P" and "O" to be Normally Open, meaning that the circuit will close (be connected) if the relay engages.

- Use the "S" if you need the connection from "P" and "S" to be Normally Closed, meaning that the circuit will open (be disconnected) if the relay engages.

Click the link to add information to this solution:
I purchased your single relay and need to know what wire go s to the signal in

Hi. The relay that we sell here:
https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Has the same relay as the parallel breakout board:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

And contains three terminals: "S", "P" and "P". The "P" is always connected and will be the connection between the "S" or the "O" depending on if you need the connection to be Normally Closed (NC) or Normally Open (NO).

- Use the "O" if you need the connection from "P" and "O" to be Normally Open, meaning that the circuit will close (be connected) if the relay engages.

- Use the "S" if you need the connection from "P" and "S" to be Normally Closed, meaning that the circuit will open (be disconnected) if the relay engages.

Click the link to add information to this solution:
I purchased your single relay and need to know what wire go s to the signal in

Yes, a 5v relay board can be connected to a spindle. Relays generally have terminals labeled S, O and P and you will want to pass one of your main wires "through" the P and S terminals or the P and O terminals depending if you want normally closed or normally open function.

Refer to Step #8 on this page to get the full instructions on how to use a relay to control the spindle or router.

https://buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto

User response:
I have the USB board. I was thinking of wiring a 5v relay board to the breakout board labeled (spindle) using the GND and (arrow) which i think is 5vdc. I will need this relay board to operate my router. Thanks

Buildyourcnc response:
Yes, those terminals are to control the relay (engage the relay). On the switch part of the relay, the router main poser wire (say, the live, black, wire) would pass through this switch portion of the relay.

Click the link to add information to this solution:
Can I wire in a 5vdc relay board to the spindle relay for my router. Gnd would be negative and the arrow would be positive right?

To move two stepper motors simultaneously with the same signal, simply wire the two stepper motor drivers to the same interface board signal terminals (CP and CW).

Additional Information:
using a ardino uno controller and a cnc sheild on top of that how to wirer 2 motors to 1 axis its the x axis ?

Click the link to add information to this solution:
I have my motors wired like the wiring diagram I have two motors on Y axis how do I wire the second motor

The stepper motor does not connect to a relay. The driver controls the stepper motor movement and direction.

Click the link to add information to this solution:
I have 8 wires the red andblue are to A+ yellow and black are A- white and brown to B+ and green and orange to B- I don't have any more wires to wire to the relay

Use the datasheet associated to the motor that you purchased. Use the bipolar parallel configuration to optimum performance. The datasheets are located in their respective motor product pages. Just click on the motion electronics at the left and scroll down to the motor you have and click on the title, or datasheet link next to the motor. The datasheet will either be in the form of a pdf, or within the instructions on that product page.

Additional Information:
wiring diagram



Additional Information:


Additional Information:

Click the link to add information to this solution:
How do I connect my motor wires to the driver?

If the motor has 8 wires, you will need to wire the stepper motor in bipolar parallel. This motor (425 oz-in) is wired as follows:

Red and Blue wires to A+ on driver
Yellow and Black wires to A- on driver
White and Brown wires to B+ on driver
Orange and Green wires to B- on driver

Click the link to add information to this solution:
[54] There are 8 wires on this motor. How do you connect to the driver?

Here is how to connect your router to the parallel breakout board through the on-board relay. You will need a spare extension cord. You will need to remove a portion of the outer jacket of the extension cord to expose the white, black and green wires (white = neutral, black = live and green = ground), understanding that the neutral and live create the completed circuit.

See this image of a similar connection. The terminal has the same connections.
https://www.buildyourcnc.com/images/vacuum-pressure-controller-relay-terminals-700.JPG

Image of the relay terminal:
https://www.buildyourcnc.com/images/breakoutboardrelayNONC.PNG

The live/black wire would be cut and one end of the cut would be secured into the P terminal and the other cut end would be secured into the S terminal. The live and ground wire would be uncut and travel from the plug to the router.


Additional Information:
You can also connect other high powered devices to the breakout board using any of the output terminals. You will need to supply extra relays like the one shown here:
https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Or you can find SSRs (Solid State Relays) that will accept 5v to drive the relay coil. Make sure the SSR will protect the 5V line from Back EMF as there is a coil in the relay. The one we sell contains a fly-back diode to protect the 5v terminal.

Click the link to add information to this solution:
I have your breakout board with relay parallel port , how can I wire up a regular router to that board so I can control the router

Have you watched this video by any chance?

Click the link to add information to this solution:
Could you please tell me how to wire the pokeys57 and driver DM860T or gecko driver ??

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

Pul+ is the Step+ and Pul- is the Step-. Pul is short for pulse. A pulse will create a step. Don't worry about the enable terminals.

On the x-axis, pin #2 can go to pul- and pin #3 can go to dir-. The 5v will go to pul+ and dir+. The configuration for each axis for step will be active low and toggle active low for the dir on each axis to make it go in the direction desired.

Next time, purchase the drivers from us and you will have fewer problems.

Additional Information:


Additional Information:


Additional Information:


Additional Information:


Additional Information:
Hi, I have an IHSS57-36-20 stepper motor with integrated driver (pulse mode) in my printer but it looks the paper moving distance is changing according to the paper tension. Has this version any encoder or I lose some steps?
Thanks, John

Additional Information:
pin #2 can go to pul- and pin #3 can go to dir-

Additional Information:
pin #2 can go to pul- and pin #3 can go to dir-

Additional Information:
pin #2 can go to pul- and pin #3 can go to dir-

Click the link to add information to this solution:
My driver has Pul+,Pul-,Dir+,Dir-,Ena+,Ena-. How do I connect the driver to my BoB.

CP+ to COM
CP- to STEP
CP+ to CW+ (small jumper wire)
CW- to DIR

Additional Information:
If the driver does not have CP or CW labels, the CP is Step and the CW is Direction or DIR. If you connect the 5v to CP+ (or Step+) and CW+ (or DIR+) and the pin to CP- (or Step-) and another pin to CW- (or DIR-), then in software, the configuration for the step on that axis must be active low. Otherwise, if you connect the GND to CP- (or Step-) and CW- (or DIR-) and the pin to CP+ (or Step+) and another pin to CW+ (or DIR+), then in software, the configuration for the step on that axis must be active high.

Additional Information:
If you have a driver that is labeled pul, dir and ena: Pul+ is the Step+ and Pul- is the Step-. Pul is short for pulse. A pulse will create a step. Don't worry about the enable terminals.

On the x-axis, pin #2 can go to pul- and pin #3 can go to dir-. The 5v will go to pul+ and dir+. The configuration for each axis for step will be active low and toggle active low for the dir on each axis to make it go in the direction desired.

Additional Information:


Additional Information:


Additional Information:


Additional Information:

Click the link to add information to this solution:
HOW DO I WIRE FROM THE BREAKOUT BOARD TO DRIVER?

The Mach3 USB Interface Board is designed to handle an output current of 50mA. These outputs are generally not suitable for heavy loads like Spindle Governor Relays (SGRs)​​. Given that your SGR pulls 2.6 Amps, it exceeds the capacity of the Mach3 USB Interface Board's output. Therefore, directly switching the SGR using the Mach3 USB Interface Board is not advisable. Instead, using your existing C36 rev1.1 board as an intermediary would be the recommended approach. This board can handle higher currents and will act as a buffer, protecting the Mach3 USB Interface Board from being overwhelmed by the higher current demand of your SGR.

Click the link to add information to this solution:
[575] How many Amps can the output handle? My SGR pulls 2.6 Amps so I need to know if the output can handle that much.

All you need is a CNC controller like the following options:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

This controller is easy to connect using standard wire screw terminals and works with the mach3 control software.

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

This controller is a little bit more difficult to connect, but is a more feature-rich controller and will work with both mach3 and mach4 CNC control software titles.

Specifically, a CNC controller connects to the computer via a USB cable and connects to the motor drivers. These controllers also connect to the limit switches, spindle/router control, air/fluid/mist control, etc.

Click the link to add information to this solution:
Can you sell me a kit to control my motor from the pc? I already have a motor, driver and power supply.

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I have your mach3 USB BoB, do you guys sell a torch control relay I can wire up to turn my plasma torch on and off and how I would wife that too this BoB?

Check step 9 on this page: http://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
IF YOU HAVE CIRCUIT (OR PICTURE) OF HOW THIS RELAY IS CONNECTED TO THE ROUTER

If you purchased the ArtCAM from us, please send an email to us at customerservice@buildyourcnc.com with the name used with making the order and we will contact the developer to send you the license.

Click the link to add information to this solution:
i have Artcam 2013 for an General Inc. Icarver 40913. My computer crash with the Licenses from Delcam i would like to know how to get the licenses.

Since the pump will use a standard 12v power supply, you will have two wires. One of those wires will be connected from the power supply to the pump. The other wire will be connected to the power supply and the pump, but cut that wire and connect one side of it in the P terminal and the other end in the S or the O terminal depending on if you need the connection as NO (Normally Open) or NC (Normally Closed).

Step number 9 in the instruction will have the relay connection information:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
I wpold like to know how to hook up my water pump (12vdc 9 amp) to turn it on and off using Mach 3. I have your Blue Brew break-out board Rev. 2.8 dated 8-12. Explain how the three relay connections work for this application? Thanks.

If the motor has 8 wires, you will need to wire the stepper motor in bipolar parallel. This motor (425 oz-in) is wired as follows:

Red and Blue wires to A+ on driver
Yellow and Black wires to A- on driver
White and Brown wires to B+ on driver
Orange and Green wires to B- on driver

Click the link to add information to this solution:
how do I connect an 8 wire motor to a driver?