I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

Question #: 13532

Question: I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

Current Solution

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Respond:

Other Possible Solutions to this Question

I have your mach3 USB BoB, do you guys sell a torch control relay I can wire up to turn my plasma torch on and off and how I would wife that too this BoB?
We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V
Click the link to add information to this solution:
I have your mach3 USB BoB, do you guys sell a torch control relay I can wire up to turn my plasma torch on and off and how I would wife that too this BoB?
I have your Mach3 usb interface board and am interested in the relay board to turn plasma torch on/off. I have a different relay board that doesn't work, it needs 0/5v from output pin to trigger and the usb board doesn't put out 5 volts. Does this relay board need 5v on output or will work fine with this usb controller?
The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.
Click the link to add information to this solution:
I have your Mach3 usb interface board and am interested in the relay board to turn plasma torch on/off. I have a different relay board that doesn't work, it needs 0/5v from output pin to trigger and the usb board doesn't put out 5 volts. Does this relay board need 5v on output or will work fine with this usb controller?
I have your breakout board with relay parallel port , how can I wire up a regular router to that board so I can control the router
Here is how to connect your router to the parallel breakout board through the on-board relay. You will need a spare extension cord. You will need to remove a portion of the outer jacket of the extension cord to expose the white, black and green wires (white = neutral, black = live and green = ground), understanding that the neutral and live create the completed circuit.

See this image of a similar connection. The terminal has the same connections.
https://www.buildyourcnc.com/images/vacuum-pressure-controller-relay-terminals-700.JPG

Image of the relay terminal:
https://www.buildyourcnc.com/images/breakoutboardrelayNONC.PNG

The live/black wire would be cut and one end of the cut would be secured into the P terminal and the other cut end would be secured into the S terminal. The live and ground wire would be uncut and travel from the plug to the router.

Additional Information:
You can also connect other high powered devices to the breakout board using any of the output terminals. You will need to supply extra relays like the one shown here:
https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Or you can find SSRs (Solid State Relays) that will accept 5v to drive the relay coil. Make sure the SSR will protect the 5V line from Back EMF as there is a coil in the relay. The one we sell contains a fly-back diode to protect the 5v terminal.
Click the link to add information to this solution:
I have your breakout board with relay parallel port , how can I wire up a regular router to that board so I can control the router
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.
Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.
Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.
HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE
The motor that is attached to the 4th axis is wired as follows:

The motor should have red, green yellow and blue wires coming form the motor. The red and green are paired as one coil and the yellow and blue is paired as the other coil. You can wire the motor to a 3.0 amp driver with red to A+, green to A-, Yellow to B+ and Blue to B-
Click the link to add information to this solution:
HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE
I wpold like to know how to hook up my water pump (12vdc 9 amp) to turn it on and off using Mach 3. I have your Blue Brew break-out board Rev. 2.8 dated 8-12. Explain how the three relay connections work for this application? Thanks.
Since the pump will use a standard 12v power supply, you will have two wires. One of those wires will be connected from the power supply to the pump. The other wire will be connected to the power supply and the pump, but cut that wire and connect one side of it in the P terminal and the other end in the S or the O terminal depending on if you need the connection as NO (Normally Open) or NC (Normally Closed).

Step number 9 in the instruction will have the relay connection information:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay
Click the link to add information to this solution:
I wpold like to know how to hook up my water pump (12vdc 9 amp) to turn it on and off using Mach 3. I have your Blue Brew break-out board Rev. 2.8 dated 8-12. Explain how the three relay connections work for this application? Thanks.
How do I get started I would like to build a cnc router. Making the machine I can do, but I am weak on cad,cam and mach3. I am thinking about a 4’x4’. Do you have plans I can buy?
We are developing plans for our machine, but they are not completed yet. Please let me know if you would like to be added to our list of customers wanting plans. Thanks,

Additional Information:
If you have specific questions regarding CAD, CAM and Control, please add another question to the customer service and I will answer them in detail.
Click the link to add information to this solution:
How do I get started I would like to build a cnc router. Making the machine I can do, but I am weak on cad,cam and mach3. I am thinking about a 4’x4’. Do you have plans I can buy?
I AM PUTTING TOGETHER THE BLACKFOOT AND USING A PORTER CABLE ROUTER. CONFUSED ON HOW TO RELAY ROUTETR WITH USB BOARD. IS THERE ANOTHER SWITCH THAT GOES BETWEEN BOARD ROUTER SO PLANET CNC CAN TURN PERHAPS VACUUM OFF?
We are currently working on a relay board that will connect to USB breakout board, and the router/spindle for both the on/off function. Unfortunately we still do not have it completed or ready to be placed on our website, but it is in the final stages of testing. Please check back regularly for updated stock!

Here is a link to a tutorial for a DIY relay circuit:

There is no vacuum control on the Planet-CNC program, however you could use the same concept of the router/spindle on/off using the relay circuit. Although you will have to use either the flood or mist function for the vacuum.
Click the link to add information to this solution:
I AM PUTTING TOGETHER THE BLACKFOOT AND USING A PORTER CABLE ROUTER. CONFUSED ON HOW TO RELAY ROUTETR WITH USB BOARD. IS THERE ANOTHER SWITCH THAT GOES BETWEEN BOARD ROUTER SO PLANET CNC CAN TURN PERHAPS VACUUM OFF?
Great site. I saw your videos of wiring the Mach3 USB controller. You place the drivers next to the Steppers. This means that you have very long leads to the USB Board? What about the placement of the controlling PC? Is it a problem to have the USB board, PSUs and Drivers in a control box and long leads to the steppers? Thank you.
I also place the controller very close to the drivers (on the back of the gantry). All of the cables are shielded. The only long cables are the mains power cables and the USB cable. The USB cable is shielded and contains active repeaters.

There is no problem putting all of the electronics in a box and using long cables to the motors. This is the way I did it for a very long time.
Click the link to add information to this solution:
Great site. I saw your videos of wiring the Mach3 USB controller. You place the drivers next to the Steppers. This means that you have very long leads to the USB Board? What about the placement of the controlling PC? Is it a problem to have the USB board, PSUs and Drivers in a control box and long leads to the steppers? Thank you.
i would like to turn on my water pump with out3 or 4 when i turn on the spindle. I have Mach3 working with the spindle on out1and 2. I have a relay wiredbut cant get out3 to flip.
Take a look at these two videos that I created today on Instagram on the proper wiring of a relay to the Mach3 USB controller.

https://www.instagram.com/tv/CMYGGBtj3cq/?utm_source=ig_web_copy_link
https://www.instagram.com/tv/CMYLvq9DXVK/?utm_source=ig_web_copy_link

Don't forget to watch the initial video on the Mach3 USB outputs on the Mach3 USB product page (last video on that page):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board
Click the link to add information to this solution:
i would like to turn on my water pump with out3 or 4 when i turn on the spindle. I have Mach3 working with the spindle on out1and 2. I have a relay wiredbut cant get out3 to flip.
[422] I have a probotix cnc router purchased in 2014, used to run on linyx, now Mach3, WindowsXP, printer port, i would like to be able to use a modern computer usb, do you have something like a plug & play or control box i can wire this into, 2 Y axis, i lost my auto tool length when i switched to XP also, any help appreciated
You have motors and drivers that already work with your machine (unless the drivers are an all-in-one setup and not modular. I would advise you to keep your current electronics and replace the parallel port breakout board with a controller that uses the USB to operate.

Here are two controllers that work under Mach3, or Mach3 or Mach4:
Mach3 USB controller (works under Mach3 only)
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board
Pokeys57CNC full-featured controller works under Mach3 or Mach4:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Alternatively, you can purchase a complete plug-and-play system or have your control system sent over to Buildyourcnc to modify the control system to use one of the above controllers.
Click the link to add information to this solution:
[422] I have a probotix cnc router purchased in 2014, used to run on linyx, now Mach3, WindowsXP, printer port, i would like to be able to use a modern computer usb, do you have something like a plug & play or control box i can wire this into, 2 Y axis, i lost my auto tool length when i switched to XP also, any help appreciated
HEY ! I HAVE PURCHASED A VFD WITH MATCHING SPINDLE 1.5KW AND CONTROL PROGRAM UCCNC. MY INTERFACE CARD IS DB25, THE QUESTION HOW DO CONNECT TO DB25 SO THAT CAN SPEED UCCNC? SINCERELY "CNC BEGINNERS"
Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.
Click the link to add information to this solution:
HEY ! I HAVE PURCHASED A VFD WITH MATCHING SPINDLE 1.5KW AND CONTROL PROGRAM UCCNC. MY INTERFACE CARD IS DB25, THE QUESTION HOW DO CONNECT TO DB25 SO THAT CAN SPEED UCCNC? SINCERELY "CNC BEGINNERS"
Hi I am trying to activate Mach3 USB Controller Output Terminals to activate a plasma from a output relay. I have looked at the video and applied 24VDC to 24v and dcm and measured from 24v and out1 and get no voltage when activating torch on mach3. The output 1 or 2 does not work.
Take a look at these two videos that I created today on Instagram on the proper wiring of a relay to the Mach3 USB controller.

https://www.instagram.com/tv/CMYGGBtj3cq/?utm_source=ig_web_copy_link
https://www.instagram.com/tv/CMYLvq9DXVK/?utm_source=ig_web_copy_link

Don't forget to watch the initial video on the Mach3 USB outputs on the Mach3 USB product page (last video on that page):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board
Click the link to add information to this solution:
Hi I am trying to activate Mach3 USB Controller Output Terminals to activate a plasma from a output relay. I have looked at the video and applied 24VDC to 24v and dcm and measured from 24v and out1 and get no voltage when activating torch on mach3. The output 1 or 2 does not work.
Hi I am trying to activate Mach3 USB Controller Output Terminals to activate a plasma from a output relay. I have looked at the video and applied 24VDC to 24v and dcm and measured from 24v and out1 and get no voltage when activating torch on mach3. The output 1 or 2 does not work.
Take a look at these two videos that I created today on Instagram on the proper wiring of a relay to the Mach3 USB controller.

https://www.instagram.com/tv/CMYGGBtj3cq/?utm_source=ig_web_copy_link
https://www.instagram.com/tv/CMYLvq9DXVK/?utm_source=ig_web_copy_link

Don't forget to watch the initial video on the Mach3 USB outputs on the Mach3 USB product page (last video on that page):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board
Click the link to add information to this solution:
Hi I am trying to activate Mach3 USB Controller Output Terminals to activate a plasma from a output relay. I have looked at the video and applied 24VDC to 24v and dcm and measured from 24v and out1 and get no voltage when activating torch on mach3. The output 1 or 2 does not work.
Hi I am trying to activate Mach3 USB Controller Output Terminals to activate a plasma from a output relay. I have looked at the video and applied 24VDC to 24v and dcm and measured from 24v and out1 and get no voltage when activating torch on mach3. The output 1 or 2 does not work.
Take a look at these two videos that I created today on Instagram on the proper wiring of a relay to the Mach3 USB controller.

https://www.instagram.com/tv/CMYGGBtj3cq/?utm_source=ig_web_copy_link
https://www.instagram.com/tv/CMYLvq9DXVK/?utm_source=ig_web_copy_link

Don't forget to watch the initial video on the Mach3 USB outputs on the Mach3 USB product page (last video on that page):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board
Click the link to add information to this solution:
Hi I am trying to activate Mach3 USB Controller Output Terminals to activate a plasma from a output relay. I have looked at the video and applied 24VDC to 24v and dcm and measured from 24v and out1 and get no voltage when activating torch on mach3. The output 1 or 2 does not work.
Hi I am trying to activate Mach3 USB Controller Output Terminals to activate a plasma from a output relay. I have looked at the video and applied 24VDC to 24v and dcm and measured from 24v and out1 and get no voltage when activating torch on mach3. The output 1 or 2 does not work.
Take a look at these two videos that I created today on Instagram on the proper wiring of a relay to the Mach3 USB controller.

https://www.instagram.com/tv/CMYGGBtj3cq/?utm_source=ig_web_copy_link
https://www.instagram.com/tv/CMYLvq9DXVK/?utm_source=ig_web_copy_link

Don't forget to watch the initial video on the Mach3 USB outputs on the Mach3 USB product page (last video on that page):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board
Click the link to add information to this solution:
Hi I am trying to activate Mach3 USB Controller Output Terminals to activate a plasma from a output relay. I have looked at the video and applied 24VDC to 24v and dcm and measured from 24v and out1 and get no voltage when activating torch on mach3. The output 1 or 2 does not work.
Hi I am trying to activate Mach3 USB Controller Output Terminals to activate a plasma from a output relay. I have looked at the video and applied 24VDC to 24v and dcm and measured from 24v and out1 and get no voltage when activating torch on mach3. The output 1 or 2 does not work.
Take a look at these two videos that I created today on Instagram on the proper wiring of a relay to the Mach3 USB controller.

https://www.instagram.com/tv/CMYGGBtj3cq/?utm_source=ig_web_copy_link
https://www.instagram.com/tv/CMYLvq9DXVK/?utm_source=ig_web_copy_link

Don't forget to watch the initial video on the Mach3 USB outputs on the Mach3 USB product page (last video on that page):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board
Click the link to add information to this solution:
Hi I am trying to activate Mach3 USB Controller Output Terminals to activate a plasma from a output relay. I have looked at the video and applied 24VDC to 24v and dcm and measured from 24v and out1 and get no voltage when activating torch on mach3. The output 1 or 2 does not work.
Hi I am trying to activate Mach3 USB Controller Output Terminals to activate a plasma from a output relay. I have looked at the video and applied 24VDC to 24v and dcm and measured from 24v and out1 and get no voltage when activating torch on mach3. The output 1 or 2 does not work.
Take a look at these two videos that I created today on Instagram on the proper wiring of a relay to the Mach3 USB controller.

https://www.instagram.com/tv/CMYGGBtj3cq/?utm_source=ig_web_copy_link
https://www.instagram.com/tv/CMYLvq9DXVK/?utm_source=ig_web_copy_link

Don't forget to watch the initial video on the Mach3 USB outputs on the Mach3 USB product page (last video on that page):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board
Click the link to add information to this solution:
Hi I am trying to activate Mach3 USB Controller Output Terminals to activate a plasma from a output relay. I have looked at the video and applied 24VDC to 24v and dcm and measured from 24v and out1 and get no voltage when activating torch on mach3. The output 1 or 2 does not work.
Hi I am trying to activate Mach3 USB Controller Output Terminals to activate a plasma from a output relay. I have looked at the video and applied 24VDC to 24v and dcm and measured from 24v and out1 and get no voltage when activating torch on mach3. The output 1 or 2 does not work.
Take a look at these two videos that I created today on Instagram on the proper wiring of a relay to the Mach3 USB controller.

https://www.instagram.com/tv/CMYGGBtj3cq/?utm_source=ig_web_copy_link
https://www.instagram.com/tv/CMYLvq9DXVK/?utm_source=ig_web_copy_link

Don't forget to watch the initial video on the Mach3 USB outputs on the Mach3 USB product page (last video on that page):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board
Click the link to add information to this solution:
Hi I am trying to activate Mach3 USB Controller Output Terminals to activate a plasma from a output relay. I have looked at the video and applied 24VDC to 24v and dcm and measured from 24v and out1 and get no voltage when activating torch on mach3. The output 1 or 2 does not work.