If your Z axis is moving in the opposite direction, go into Mach3, click on config, ports & pins, then click on the motor outputs tab. You will see the axes labeled on the left and the parameters labeled on the top of this dialog box. Toggle the dir low active for the z-axis.

Additional Information:
What if I'm having the same issue on a different axis?

Additional Information:
You can follow the same procedure as with the z-axis. When you get to the motors outputs tab, toggle the dir low active checkbox for the axis that you would like to change.

If you are using another control program, let me know and I will add the recommended action here.

Additional Information:
Girbl

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:

Click the link to add information to this solution:
My Z-axis seems to be reversed on a fully assembled machine... I've tried reversing it in the config settings on Mach 3, but to no avail. What do I need to do? IS this a wiring issue that was not done correctly at the factory?

Come on over and we will assist you in any way you need.

Click the link to add information to this solution:
I purchased a Blackfoot 4ft X 8ft in 2015 I have yet to run it. Do y’all offer any classes that can help me?? I would very much like to have this machine running. Thank you in Dayton Tx

The blackFoot uses the same electronics and motors as the blackToe (2'x4') machine. The only parts that change are the gantry horizontal structural parts which may be relatively easy for you to change. We can send you those parts if you are interested in a smaller unit.

Click the link to add information to this solution:
I have a Blackfoot that was purchased in 2017, after the purchase we moved and I haven’t been able to find room for it... would you be interested in buying it back or trading for something smaller. The Blackfoot and computer have never run but I did purchase it assembled. Thanks in advance, scott

The license file should be called Mach1Lic.Dat, you can copy it to a Mach3 folder on another computer and it will register the program.

Click the link to add information to this solution:
You sent my my activation code which I have jealously, guarded on my Desktop till needed, now, unfortunately I cant get it to copy from Desktop to the computer and Mach3, is it possible to get advice on this or maybe a replacement that can be put on a stick then plugged into my Mach3 computer. This is how I have tried but when I open the folder it is empty. Thanks for your patience with me.

You have motors and drivers that already work with your machine (unless the drivers are an all-in-one setup and not modular. I would advise you to keep your current electronics and replace the parallel port breakout board with a controller that uses the USB to operate.

Here are two controllers that work under Mach3, or Mach3 or Mach4:
Mach3 USB controller (works under Mach3 only)
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board
Pokeys57CNC full-featured controller works under Mach3 or Mach4:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Alternatively, you can purchase a complete plug-and-play system or have your control system sent over to Buildyourcnc to modify the control system to use one of the above controllers.

Click the link to add information to this solution:
[422] I have a probotix cnc router purchased in 2014, used to run on linyx, now Mach3, WindowsXP, printer port, i would like to be able to use a modern computer usb, do you have something like a plug & play or control box i can wire this into, 2 Y axis, i lost my auto tool length when i switched to XP also, any help appreciated

We are developing plans for our machine, but they are not completed yet. Please let me know if you would like to be added to our list of customers wanting plans. Thanks,

Additional Information:
If you have specific questions regarding CAD, CAM and Control, please add another question to the customer service and I will answer them in detail.

Click the link to add information to this solution:
How do I get started I would like to build a cnc router. Making the machine I can do, but I am weak on cad,cam and mach3. I am thinking about a 4’x4’. Do you have plans I can buy?

CamBam specifically creates the g-code (machining operations) instructions to be loaded into Mach3. Make sure in your CamBam g-code file parameters, you are using the Mach3 post processor. If you have already done this, let me know. If you are not sure how to do this, let me know.

Click the link to add information to this solution:
I am having trouble connecting the cambam program with my Mach3 to my 4X8 Blackfoot CNC machine. Where can I get help on this issue. Have had my machine since 2015 and have not been able to use it. Thank you

The Mach3 USB will not work with Linux CNC. You can use our parallel breakout baord instead (if you have a computer that has a parallel port available).

Here is the link to that interface:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hello. I'm currently building my first CNC router, and I'm powering it with a 3 axis electronics kit that was purchased through your site. I chose to get the Mach 3 USB Breakout board, but now I'm wanting to try to use Linux CNC to work with the computer I have available. Will that work with this board?

You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

Yes, we can help you with leveling your CNC machine even if you didn't purchase it from us.

Click the link to add information to this solution:
[789] I need to level my cnc machine, but I didn't purchase it from you, so: Do you offer tech support with leveling a cnc? Because I don't see this problem listed .And: Do you offer support if my machine was purchased in China or from another vendor?

We like the water cooled spindles since they don't blow the chips around the shop. The air cooled spindles have a force of air that partly makes the vacuum and dust shoe non effective, unless we design a diverter, which limits the cooling effect for the spindle.

Click the link to add information to this solution:
For our cnc we're searching for an air cooled spindle with 2.2 kw. On this page we've only found water cooled ones. Is it possible to get an air cooled spindle from you or do you have special reasons for don't selling them?

it is possible to install 2 motors on a single axis but you will require another driver and motor, but wire it directly to the same pins on your breakout board. Also the orientation of your motor since it is opposite side of the original so getting it to move accordingly to the original motor it will need to be orientated correctly. The slight shift could be the cause of the rod not being completely flat where the set screws are suppose to tighten the sprocket to the rod, so sanding it to a flatter surface might fix the shift in directions.
Currently do not have a kit or schematic available.

Click the link to add information to this solution:
Hello, I have a BlackToe 2 x 4 machine. I was wondering if it could be beneficial, or even possible to install two motors on the x-axis (one one each chain drive sprocket). I am noticing a slight shift in the gantry with each reversal of direction. If so, do you have a kit or schematic for this? Thanks

This will point you in the right direction.
http://vancura.biz/files/Documents/CNC/YL620-A%20Setup%20table%20190707.pdf

Additional Information:

Click the link to add information to this solution:
I have a YL620 VFD and the 2.2 kw spindle. The programming that is on the buildyourcnc web site is different in the PO/PD parameters. Do you have the VFD settings for the parameters using the P00.00 format?

MY VFD SHOW E.O.C.A error


Additional Information:
EOCA light on my VFD


Additional Information:


Additional Information:

Click the link to add information to this solution:
I have a YL600 VFD and the 2.2 kw spindle. The programming that is on the buildyourcnc web site is different in the PO/PD parameters. Do you have the VFD settings for the parameters using the P00.00 format0

Currently our greenBull can only accommodate a 40W laser tube due to the size and current mounts on the spindle/laser hybrid assembly!

However please contact 281-815-7701 for further assistance with the greenBull machine.

Click the link to add information to this solution:
I am interested in the GreenBull 4x8 CNC machine kit you have; I also wish to get the laser attachment but I was wondering if its possible to have the laser larger than a 40w, say in the 80-150w range?

We do offer discounts for academic institutions and instructors. Please contact us via the phone number above to inquire about our academic discount.

Click the link to add information to this solution:
I need to know if you have prices for educators, or other ways that a teacher could procure a blackToe 2'x4' CNC router. I apologize that this is sort of a bold question, as your routers are already well-priced.

All USB boards, are tested and checked before shipment for all axis, and inputs. Here is a link with clear instructions on how to setup Planet-CNC (http://www.planet-cnc.com/faq/machine_setup/).

Please check continuity and for any crossover disruption when wiring your board, try to wire each as cleanly and with out crossing any live power wires and or motor motion wires.

Click the link to add information to this solution:
I have a usb cnc driver board on your 1'x3' cnc and i cant get the z+ limit switch to stop the machine in the provided software. It registers the button but doesn't inhibit movement. inversly the button works when selected as '-' for negative movement.

As long as the bearing has a minimum thickness of 1/4" and 9/32" is a bit thicker, there will be no problem with the book build using the bearing that is 1/32" thicker. There is actually more surface area which is better.

Click the link to add information to this solution:
I am building the CNC in your book - Build you own CNC Machine. One of the bearing thicknesses is 1/4" I can't find that bearing online. I can find 9/32, will that be a problem. Do you have a source? Thx

Hi, you can call me at the 281-815-7701 number. Please leave a message when you call as most of the calls are screened to avoid scam calls. You can also email me at customerservice@buildyourcnc.com or phooddaniel@berkeley.edu.

The newer kits that are featured on the home page include everything you need except a computer and software. The legacy CNC routers that are located in the CNC machines menu selection include all of the parts for the gantry, but you will need to build the table yourself. All of the information on the measurements to be followed for the table construction are on the machine pages.

Click the link to add information to this solution:
I am looking at getting a 4x8 cnc router kit. I am having a hard time figuring out what is included in the kit and what else i will need to buy with it to get off the ground and running. Is there someone i could talk to to walk me through it? If not, can you break down what all I need to go from scratch to a running set up? thanks