To replace all of the electronics for a 4 axis system with all NEMA 34 motors, you will need the following components:

4 NEMA 34 stepper motors:
https://buildyourcnc.com/item/electronicsAndMotors-nema34-651ozin

4 drivers (one driver for each motor):
https://buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

One controller:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

24v Powers supply for the controller:
https://buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

2 48V power supplies for the motors and drivers:
https://buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-36v-48v

Click the link to add information to this solution:
i have a 4 axis cnc need to replace everything electronics and motor nema 34 what do i need to buy

Other items you will need if you are purchasing the electronic combo (motors, drivers, power supply and computer interface) and the hardware and plans kit:

You will need the wood to create the structure of the machine. You will need a router to serve as the cutting instrument. You will need a computer to control the machine and the software that will serve as the control program. You will also need lead screws and rails (aluminum angles). If you intend to have faster travel than 20 ipm, we recommend purchasing the 5 start lead screws so you can achieve up to 300 ipm. https://www.buildyourcnc.com/item/mechanical-leadscrews-leadnuts-!5-5-starts-10-tpi

Click the link to add information to this solution:
if i purchase the 4 Axis Electronic Combos and the Combo #1 with hardware, plans and DVD what else do i need to have a complete cnc machine

The bluchick CNC router is a perfect small format CNC that can handle most jobs. Please check here to see the latest information on this CNC router. blueChick CNC Machine. The machine can be purchased assembled. Al you will need is a computer and spindle.

Click the link to add information to this solution:
I'm looking for a complete CNC router, out the box ready to use system. Computer and software. What do you suggest? I need a working area of 12"x24"

We currently do not have any Nema motor's with a .375"/3/8" shaft diameter. The motors in stock 100 oz, 425 oz, with a 1/4" input shaft. Our 651 oz, with a 1/2" input shaft.

Click the link to add information to this solution:
Your combo kits don't specify whether they are standard NEMA motors. I need Nema 34 with a .375 shaft diameter. Which 3 axis kit work for these requirements?

Surely you know the brand motors you sold me?

Click the link to add information to this solution:
I bought your 3 axis combo and need to know what name brand is the motors and their ounces and the drivers

Yes, the redLeaf is integrated into the redLeaf, all wired and configured. It is a plug and play system.

Click the link to add information to this solution:
replacing all electronic on a small cnc would like to use the redleaf hd +4 nema 34 motors does mach 3 included already installed

Sure, please email me at customerservice@gmail.com or phooddaniel@berkeley.edu.

Additional Information:
20

Additional Information:
20

Additional Information:
20

Additional Information:
20

Click the link to add information to this solution:
[820] i will be using nema 17 closed loop motors for my cnc build. I need a price for my build. It will be put on a emco 3 unimat lathe.

If you are looking for the drivers to pair with NEMA 34 stepper motors, you can find the 6.0 amp drivers here:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

The other electronics to send the signals to the 6.0 amp drivers (the control board that operates with the control software) is subject to personal preference, but here they are listed:

Our breakout board (works with Mach3 and LinuxCNC and requires a parallel port on your computer):
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

The PoKeys57CNC (works with Mach3 and Mach4):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Generic USB breakout board (works with Mach3):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Additional Information:
Do I need a driver for every motor or can I use one driver for all four motors

Additional Information:
Each motor needs its own driver.

Click the link to add information to this solution:
I HAVE NEMA 34 MOTORS BUT NEED THE ELECTRICAL COMPONENTS DO YOU A KIT WITHOUT INCLUDED?

Have you considered reversing the A and B coils on one of the motors to the drivers? This will cause the motor to spin in the opposite direction. This is the easiest method. Using the HEX inverter is a more complex method and not recommended for simple driving tasks.

Click the link to add information to this solution:
I have two nema 34 motors on my gantry and ordered a hex inverter, now I need to wire it correctly. What type of wiring hardware do I need and I will need a wiring diagram also. Please help.

Have you considered reversing the A and B coils on one of the motors to the drivers? This will cause the motor to spin in the opposite direction. This is the easiest method. Using the HEX inverter is a more complex method and not recommended for simple driving tasks.

Click the link to add information to this solution:
I have two nema 34 motors on my gantry and ordered a hex inverter, now I need to wire it correctly. What type of wiring hardware do I need and I will need a wiring diagram also. Please help.

If you do not have electronics for your CNC, you will need stepper motors (or servos) that will fit your torque requirements, drivers for the motors, a power supply, applicable wires, and an interface board for computer communication. We sell electronic combo kits here https://buildyourcnc.com/electronicscombo.aspx

Click the link to add information to this solution:
I just bought a 3040 800 watt cnc. What electronics do i need to buy to run it?

if you purchased the USB interface, you will need planet-cnc software rather than Mach3, and you will need a usb cable to connect the usb interface to the computer.

The blackToe 2x4 CNC Machine Kit with optional table will need wire to connect the electronics. Don't forget to get some end mills to use for cutting the intended material.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
if buy a 3 axis cnc combo, which software would I need for working this combo?

If you are looking for the drivers to pair with NEMA 34 stepper motors, you can find the 6.0 amp drivers here:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

The other electronics to send the signals to the 6.0 amp drivers (the control board that operates with the control software) is subject to personal preference, but here they are listed:

Our breakout board (works with Mach3 and LinuxCNC and requires a parallel port on your computer):
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

The PoKeys57CNC (works with Mach3 and Mach4):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Generic USB breakout board (works with Mach3):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Additional Information:
Do I need a driver for every motor or can I use one driver for all four motors

Additional Information:
Each motor needs its own driver.

Click the link to add information to this solution:
I have Nema 34 motors but I need the electrical components do you have a kit without motors included?

If you were to buy all of that, only thing you'll need is the mach3 software to run the machine.

Click the link to add information to this solution:
I am interested in purchasing the Green Lean complete kit and also buy the ArtCamPro what other software will I need to up and running?

Yes, I will need to know more specifics of the machine so I can recommend the correct electronics.

Click the link to add information to this solution:
ok I Build my CNC machine table and now need a complete set for motor and software how you can help me

Polabs prepared step by step user guide for PoKeys57CNC and Mach4 to try answering such questions. It is available in our downloads section: https://www.poscope.com/wp-content/uploads/downloads/Pokeys/LibrariesAndPlugins/Mach4 and PoKeys57CNC - step by step guide.pdf

Additional Information:

Click the link to add information to this solution:
Using the PoKeys57CNC how to you connect two motors to the Y axis and how is Mach 4 configured for this?

Looking for a solution myself. Proper operation would be for the limit switch to only disable further travel in the effected direction while still allowing travel in the opposite direction.

As for now, I am just using the jog arrows within the software or the VGA controller.

Click the link to add information to this solution:
After limit switch is activated on planet cnc control software, what do I need to do to get axis to move again?

We will make sure that order is changed prior to shipping.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
just placed an order for 2 nema 34 and 1 24 stepper motors i meant to have be 1, 34 and 2, 24 stepper motors. I need to change that before shipping

Yes, you can use 2 motors in the same axis output, however you will still need a driver for that motor! Also depending on the orientation on which you mount the motor you might have to invert the direction of the motor, and that will be simple by swapping the A+,A-, to the B+,B- locations and vice versa, from the driver to the motor wiring.

Also you can run a slave motor using another axis on the board, and setting it up in the Planet-CNC settings.

Planet-CNC/File/Settings/Axes, here you will enter 3 in the Number of Axes location, and then change the Function of the Axis 4 to Slave 1. There you will have the 4th axis or A-axis be a slave for the x-axis.
Slave 1 - X-Axis
Slave 2 - Y-Axis
Slave 3 - A-Axis
Slave 4 - B-Axis
Etc...

Click the link to add information to this solution:
What wiring should I use to connect two motors for one axis?