You can see the component list on the hardware and plans machine (scratch build machine) since it is the same machine in the book:

https://www.buildyourcnc.com/Item/cnc-machine-scratchbuild

Additional Information:

Click the link to add information to this solution:
I purchase Build Your Own CNC Machine. where can i download PDF so i can print Large

As long as the bearing has a minimum thickness of 1/4" and 9/32" is a bit thicker, there will be no problem with the book build using the bearing that is 1/32" thicker. There is actually more surface area which is better.

Click the link to add information to this solution:
in your book - Build you own CNC Machine. Can I use 9/32" thick bearing instead of 1/4" thick?

You can see the component list on the hardware and plans machine (scratch build machine) since it is the same machine in the book:

https://www.buildyourcnc.com/Item/cnc-machine-scratchbuild

Additional Information:

Click the link to add information to this solution:
I PURCHASE BUILD YOUR OWN CNC MACHINE. WHERE CAN DOWNLOAD PDF SO PRINT LARGE

Yes, I will need to know more specifics of the machine so I can recommend the correct electronics.

Click the link to add information to this solution:
ok I Build my CNC machine table and now need a complete set for motor and software how you can help me

These machines are inherently dangerous. Before the machine moves, the machine should be clear of any person by a dimension of at the distance of a persons reach plus a few more feet. This is the policies we institute in our shop and what is recommend to all of our customers. Treat these machines as you would treat any major power tool in the shop.

With that said, you can certainly add some protective parts, but still keep folks away even with those installed. I would use the gantry side to do all of the mounting of the protective parts. Consider using sheet metal that you can bend and make a simple installation right on the gantry side.

Additional Information:

Click the link to add information to this solution:
THE CNC MACHINE IS UNSAFE WITH EXPOSED SPROCKETS THAT CAN DAMAGE FINGERS AND HAVE CLOTHING CAUGHT IN IT.

We offer as much information as possible about the design and building of CNC machines through this website and the forums at buildyourtools.com. We also still offer our "scratch build" plans at https://buildyourcnc.com/item/cnc-machine-scratchbuild, where you can order the plans and DVD to build your own machine with or without the necessary hardware components.

Our technical support staff are occupied full time assisting customers who have bought complete kits or assembled machines, and unfortunately do not have the resources to provide one-on-one advice to individuals.

Click the link to add information to this solution:
I Want to design and build my own CNC wood working machine. Do you give advice and help advice to do this?

Gcode or digital files are not available for our machines.

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I have the build your own CNC kit 3 Axis CNC Machine 2008, were can I get the Gcode or vector files for it ? I wanted to have it laser cut

The blueChick would be the perfect machine to iso route PCB boards. The A4 size is 8.3x11.7 inches and the blueChick is 12x36 inches. It's a bit larger, but you would be able to route many more PCBs. I would also recommend getting the 1.5 kW or 2.2 kW spindle for the blueChick since you will want very low runout to make the isolation routes (kerf) between traces very thin.

Click the link to add information to this solution:
I want to build my first CNC machine for PCB manufacture. I wish to manufacture at most A4 sizes. Which CNC kit do you recommend?

All of our CNC machines can cut melamine. If your application (kitchen doors) requires large cutting area, then I would recommend the following machines:

- greenBull 4x (4'x8'), 5x (5'x10') or 6x (6'x 12')

- greenLean 4'x8' vertically oriented CNC machine

- Or our Fabricator Pro 4'x8' metal CNC machine

Click the link to add information to this solution:
CAN YOU RECOMMEND WHICH CNC MACHINE TO GO WITH FOR CUTTING MELAMINE AND MAKING KITCHEN DOORS FROM MDF. ALSO DO PROVIDE TRAINING ON OPERATING SETTING UP SHOP PRODUCTION USE? THANKS

To assemble the blueChick v4.2, you will need two sets of instructions, the assembly instructions for the main body and mechanicals of the CNC machine, and the instructions to connect and test all of the electronics.

The assembly instructions are located at this URL towards the bottom of the page (click on each picture to get a larger view):

https://www.buildyourcnc.com/blueChickVersion42CNCMachineKit.aspx

The instructions to connect and test the electronics can be found at this URL:

https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

Click the link to add information to this solution:
I have a blueChick version 4.2 CNC Machine with no schematics for it is there anyway possibly i can get them so i can finish putting my cnc together

It sounds like you got a misprinted book. If you purchased it from us, please contact us directly for a replacement. If you bought it from Amazon or a third party, you'll need to contact them. General information about lead screws is available on this website and at buildyourtools.com.

Click the link to add information to this solution:
Just bought Build Your own CNC Machine book. It is missing the chapter on lead screws that is described on page 181 at the end of Chaprer 16. Where can I get this info?

As long as the bearing has a minimum thickness of 1/4" and 9/32" is a bit thicker, there will be no problem with the book build using the bearing that is 1/32" thicker. There is actually more surface area which is better.

Click the link to add information to this solution:
I am building the CNC in your book - Build you own CNC Machine. One of the bearing thicknesses is 1/4" I can't find that bearing online. I can find 9/32, will that be a problem. Do you have a source? Thx

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE MACHINE?

Yes, we have a 4 axis combo kit available under Motion Electronics.

Click the link to add information to this solution:
Can you supply an electronics package for a dual x-axis CNC machine (X, Y, Z)

That is a good question. We have not tried to weld thermoplastics using our CO2 Lasers. It is possible since the laser outputs a heat source and at the right intensity and speed, the thermoplastic can be heated and melted rather than instantaneously vaporized and off gassed. I have done research to see if CO2 laser can weld thermoplastics with positive results.

Our CO2 lasers are typical of other laser cutters on the market, so if their literature, or examples you have found, successfully weld thermoplastics, then ours will probably be able to as well.

In some cutting test with different speeds and intensities, the kerf has welded back together; however, this was caused by an unintentional process rather than an intentional one.

Click the link to add information to this solution:
Can a CO2 CNC laser machine be used for welding of thermoplastic materials?

All of our CNC machines can cut melamine. If your application (kitchen doors) requires large cutting area, then I would recommend the following machines:

- greenBull 4x (4'x8'), 5x (5'x10') or 6x (6'x 12')

- greenLean 4'x8' vertically oriented CNC machine

- Or our Fabricator Pro 4'x8' metal CNC machine

Click the link to add information to this solution:
Can you recommend which CNC machine to go with for cutting melamine and making kitchen doors from MDF. Also do you provide training on operating and setting up machine for shop production use? Thanks

The pictures of the table on the blackFoot v4.3 CNC machine page uses 2/4 studs, a torsion box, and a final top 3/4" layer.

The torsion box and the top bed layer lays on a frame constructed by 2x4 framing studs angled to resist twisting and for greater rigidity. the joints are simply connected with long screws and you can also use framing plates/ties. The torsion box is constructed of 3/4" MOD stock and has a ribbing pattern spaced around 8 inches apart. The design is similar to this: https://www.buildyourcnc.com/ModularTorsionBoxTable.aspx

The top later is simply multiple sheets of MOD 3/4" thick to conform to the required final measurement.

Click the link to add information to this solution:
The table top pictured with the blackFoot 4'x8' v4.3 CNC Machine Kit looks nice. I'd like to build one just like it. How thick is it? If it was made from multiple sheets, how did you make the butt joints?

Yes, that is not a problem at all. Give us a call.

Click the link to add information to this solution:
Can you custimize the 2'x4' CNC Machine Kit (blackToe v4.1) w/ 2.2kW Spindle into a 2'x3' Machine Kit?

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Can I purchase a computer off Amazon (I have a machine I want to use) and still use the USB interface to drive it with LinuxCNC?