If you have the laser firing using the Z direction, then you want to make sure that the thickness and clearance plane is extremely small. The time it takes for the software to think that the z axis has lowered to the depth set in the design is causing the laser to stay on in a single position for too long. Make sure that the depth is extremely small, like .0001" or the smallest amount allowed by the Vectric software. Also, make sure the clearance plane (the height that the z axis would raise to clear any protrusions like clamps and the such) is extremely low.

Click the link to add information to this solution:
I have been using a Blacktooth for some time, with Vectric2d and Mach3. I have always found that the laser burns a hole before moving off. I have always set material thickness at actual value. Should it be set very low? Also, of the many post processors supplied with 2d, which is best for Blacktooth?

We have the image at that size to encourage the purchase of the kit from us. This helps to keep buildyourcnc alive and allows us to fund development of other awesome low cost machines.

Click the link to add information to this solution:
could you make available a larger size picture of the exploded view of the BlackTooth laser cutter? I would like to use for reference when building my laser cutter, but it is too small to be really useful.

The space allotted for the laser tube on the blackTooth would not allow for a higher power laser tube. As the wattage of the laser tube increased, so does the length of the tube.

We do have a larger and more powerful laser in design and should be available in the second quarter of 2015.

Click the link to add information to this solution:
Can you install a more powerful laser/tube for us if we pick the $2100 option to have you build it? It would be assumed that there would be a new price for the machine which would reflect the cost increase for the new laser. Please say yes, I know you can physically do it. I have faith in you

it is possible to install 2 motors on a single axis but you will require another driver and motor, but wire it directly to the same pins on your breakout board. Also the orientation of your motor since it is opposite side of the original so getting it to move accordingly to the original motor it will need to be orientated correctly. The slight shift could be the cause of the rod not being completely flat where the set screws are suppose to tighten the sprocket to the rod, so sanding it to a flatter surface might fix the shift in directions.
Currently do not have a kit or schematic available.

Click the link to add information to this solution:
Hello, I have a BlackToe 2 x 4 machine. I was wondering if it could be beneficial, or even possible to install two motors on the x-axis (one one each chain drive sprocket). I am noticing a slight shift in the gantry with each reversal of direction. If so, do you have a kit or schematic for this? Thanks

Cutting metal with lasers even at 100W and 130W is difficult. The main problem is molten is a byproduct of lasing, which can severely damage the laser.

Click the link to add information to this solution:
For the XL Vertical Laser Machine I see it won't cut metal as it is only 80w. However, I noticed that you are working on 100w and 130w versions so will that be sufficient to cut through sheet metal? If so, how much longer until those are available?

As shown in the instructions the laser tube that was used was a different model which had the metal end, compared to our full glass tube models we currently ship with the machines.
So there is no difference besides appearance between the two tubes.
The focus lens should be placed in the laser nozzle assembly and not on the laser tube itself.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I bought a blacktooth laser from you about a year ago.. I am finally getting around to installing the laser tube and I noticed that my tube does't have the metal end on it like all the pictures I've seen. is this a focus lense and can I purchase one?

Yes, it is feasible to create a machine with a cutting area of 13'x15'. Your mechanical and structural systems will need to be able to span a bit more than the 13' if that will be the axis travel along the gantry.

We have not cut carpet with our lasers, but I don't see why not. With that said, be extremely careful with the materials in the rug. Read the MSDS (Material Safety Data Sheet) for the rug you intend to cut as some materials will emit corrosive and harmful gases and chemicals when lased.

Click the link to add information to this solution:
Hi I want to build a cnc laser table 13'x15' cuttting area. Is this feasible. Also would the 80watt laser be enough power to cut through carpet

To verify, you are still getting the laser tube to fire, but the laser beam is weak and cannot cut or engrave any materials correct?

Have you checked your tube's tungsten post terminals to make sure they are getting good contact?
The Laser tube and laser power supply both have manufacture warranty, please email customerservice@buildyourcnc.com for further assistance.

Click the link to add information to this solution:
Hello, I have a blacktooth laser cutter, the machine has 10hrs of work, suddenly in the middle of a job the laser beam lost all power, I can still se the purple plasma beam but with no power or intensity, the tube is fine, water is running through and there is no arcing to the chasis or some other part. I think it might be a faulty PS how can I test it, Do I have a warranty on it?

We do offer all of the parts; but it is best to purchase them a la carte. You will probably not want the hardware since this would not conform to a design in metal.

All of the mechanical parts are available here:
https://buildyourcnc.com/CNCMachineMechanicalParts.aspx

All of the electronics you would need is available here:
https://buildyourcnc.com/electronicscombo.aspx

All of the laser components are available here:
https://buildyourcnc.com/LaserComponents.aspx

And the spindles and VFDs are available here:
https://buildyourcnc.com/SpindlesAndAccessories.aspx

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hello, I'm interested in GreenBull 5'x10' CNC machine kit with 40W laser head. Is it possible to receive an offer for this size cnc machine kit with all the mechanics, electronics and laser parts, but without all the wooden parts? We would like to build this kind of laser cutter machine with metal frame and parts. And is it possible also to get 3D drawing for machine? Waiting for your answer.

Yes, if you need a replacement part on your machine please call us at 281-815-7701.

Click the link to add information to this solution:
I have a blacktooth laser engraver. The Y Axis stepper motor needs to be replaced. Can you please provide me with the information I would need to replace this motor.

Hi, you can call me at the 281-815-7701 number. Please leave a message when you call as most of the calls are screened to avoid scam calls. You can also email me at customerservice@buildyourcnc.com or phooddaniel@berkeley.edu.

The newer kits that are featured on the home page include everything you need except a computer and software. The legacy CNC routers that are located in the CNC machines menu selection include all of the parts for the gantry, but you will need to build the table yourself. All of the information on the measurements to be followed for the table construction are on the machine pages.

Click the link to add information to this solution:
I am looking at getting a 4x8 cnc router kit. I am having a hard time figuring out what is included in the kit and what else i will need to buy with it to get off the ground and running. Is there someone i could talk to to walk me through it? If not, can you break down what all I need to go from scratch to a running set up? thanks

Here is how to connect your router to the parallel breakout board through the on-board relay. You will need a spare extension cord. You will need to remove a portion of the outer jacket of the extension cord to expose the white, black and green wires (white = neutral, black = live and green = ground), understanding that the neutral and live create the completed circuit.

See this image of a similar connection. The terminal has the same connections.
https://www.buildyourcnc.com/images/vacuum-pressure-controller-relay-terminals-700.JPG

Image of the relay terminal:
https://www.buildyourcnc.com/images/breakoutboardrelayNONC.PNG

The live/black wire would be cut and one end of the cut would be secured into the P terminal and the other cut end would be secured into the S terminal. The live and ground wire would be uncut and travel from the plug to the router.


Additional Information:
You can also connect other high powered devices to the breakout board using any of the output terminals. You will need to supply extra relays like the one shown here:
https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Or you can find SSRs (Solid State Relays) that will accept 5v to drive the relay coil. Make sure the SSR will protect the 5V line from Back EMF as there is a coil in the relay. The one we sell contains a fly-back diode to protect the 5v terminal.

Click the link to add information to this solution:
I have your breakout board with relay parallel port , I have a vacuum, light on router and air pump I want to also hook up to board, can I hook those up to board and also could I had reylays to each one, what is the best way to figure this out any information would be great. Thanks

Did you install the Mach3 USB plug-in?

Make sure that you followed all of the steps and diagrams on the following page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
ABSOLUTELY NOTHING WORKS. I HAVE ALL STRUCTURE AND MECHICAL PARTS OF THE BLACKTOOTH CUTTER DONE. HOWEVER WHEN WIRE UP STEPPER MOTOR TO DRIVER. THAT MACH 3 USB CONTROLLER BOARD, TRY JOG MOTOR, WORKS! PREVIOSULY HAD PLANET CNC BREAKOUT HOWRVER, ONLY MOVED MOTORS IN ONE DIRECTION COULDNT CHANGE IT. ANY HELP WOULD BE APRECIATED

Stepper motors are known to make noises while function, however this does not affect accuracy or job function. However we recommend to check your wiring for solid connections, and for good connectivity!



On a personal note, here is one cool video dealing with making songs with stepper motors!

Click the link to add information to this solution:
I bought and built the Blacktooth laser cutter. It works, but one of the stepper motors makes a loud static hiss a second after the CNC power supply is turned on or off, and makes loud tweets and twirps when running. It seems to operate fine otherwise. I was wondering if it was "going bad" or if that is normal?

Dealing with glass co2 laser tubes, it is difficult to accurately tell if it is going out or loosing "oomph". The laser will loose its co2 levels, which will cause it to loose cutting strength.
We have noticed that the laser at its "strongest" or new state fires a purplish/reddish color laser through the tube, and when it is loosing its cutting strength it turns to a faded red orange/orange color.

Using a ammeter will only measure the current going to the tube. The PSU will not know when the tube is losing its cutting strength, so it will constantly flow the same voltage and current.


Additional Information:


Additional Information:


Additional Information:
How many dots should come out of the laser

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
What is a clear indication of a failing/failed laser tube? I know that laser tubes eventually "wear out", but how does one determine if the tube is loosing its "oomph"? My 40W Blacktooth laser tube return goes through an ammeter, so is the ammeter reading proportional to the beam strength, or can the beam die and still draw the same amount of current?

We have been quite busy during the Holiday season which is normal. This may result in extended lead times. If you would like to speak to a representative about your order please call 281-815-7701 or email customerservice@buildyourcnc.com and someone will advise you when to expect your order.

Click the link to add information to this solution:
How long does processing typically take before a Blacktooth laser cutter ships? I see a week on a lot of the answers, but my order is pushing two. Since bad luck tends to follow me around, I just want to make sure I'm still in the realm of normal processing time.

There is some variation in the outward appearance of laser power supplies due to sourcing through different vendors. However, the basic wiring requirements are the same in each case. For the unit with integrated laser controller, follow the diagram found here: https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/0/. The terminals on the signal side will have a 6 connection terminal block -- these are the ones labeled 5V, IN, G, P (or WP), L (or TTL-L), and H (or TTL-H). The High Power side will have 3 inputs for AC power, one high voltage lead, and one return line. Connect these as shown in the diagram as well: the return line goes on the "front" (beam exit end) terminal of the laser tube, the high voltage lead goes to the "back" terminal of the tube, the FG terminal (or G) receives the earth ground wire of the AC power cable, and the two AC terminals receive the line and neutral wires of the AC power cable (it doesn't matter in this case which wire goes to which terminal).

Click the link to add information to this solution:
I purchased the blackTooth Laser Engraver with integrated Laser Control Unit and have been following your instructions. I noticed that the laser tube power supply is different that what is shown in your instructions. Do you have any better wiring guides that I can follow for the version that I received?

These connectors are not necessary and they are not included in the kits anymore. I have revised the step to reflect this change. The connectors are actually an undesirable addition since that is a point at which the hoses can be disconnected during the machine operation and cause water to drop into the driver electronics.

Click the link to add information to this solution:
In the Blacktooth instruction 90 A pair of coolant hose connectors are to be installed. These didn't come with all the other parts, and aren't on the packing list. Are they really necessary? Could not the tubes just exit through these holes and go to the pump, bucket, or water container?

We only have these models in SketchUp. Is that a format that will be acceptable?

Additional Information:
Anything with basic profile dimensions will work just fine.

Click the link to add information to this solution:
Would you be able to supply solidworks files for the laser nozzle, mirror mounts, & laser tube? I plan to build a laser engraver and would like to model everything up before i start building to make sure it all fits.