Yes, with caveats. This kit includes a controller that will not be compatible, but if you use another type of controller that has web based control, you can use these electronics. Here is a list of web based control for CNC:

- Easel: The web-based software from Inventables can be accessed through Safari or other macOS-compatible web browsers.

- bCNC: A Python-based GRBL CNC command sender, although you may need to jump through some hoops to get it to run on macOS.

- Universal Gcode Sender: A Java-based software that should run on macOS if you have the Java Runtime Environment installed.

- CNCjs: Another web-based interface that you can run on macOS using Node.js.

Click the link to add information to this solution:
[50] Is there a software control package that will work with Axis Electronics Combo (For Heavy Gantry) for apple os.

The 651 oz/in NEMA 34 stepper motor does have a dual shaft. The shaft extends 19 mm at both ends.

Click the link to add information to this solution:
3 axis heavy gantry combo. Is the Nema 34 motor dual shaft?

Unfortunately, we don't sell the planet-cnc controller anymore. They made a change to their software that prohibits us from creating the open source board.

We do sell three other boards that may work for you.

The Pokeys57CNC board is the mose feature rich and will work with both Mach3 and Mach4:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

The MAch3 USB board is a good inexpensive interface that will work well if you need the interface to be USB only:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Our in-house parallel breakout board (ytou need a parallel port for this interface to work):
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay
Most motherboards have the parallel port connector on the motherboard, but not as a connector on the back of the computer case.

Click the link to add information to this solution:
Do you sell the 3 axis electronics combo , for heavy gantry , with the new Planet CNC usb controller ?

Controlling a 3-axis or 4-axis motor configuration, you will need the following items drivers/motors/controller. Our electronics combo comes with the items mentioned and with power supply/miscellaneous items.
The only other item needed will be a computer (with controller software) to communicate and view controls of your motors.
Using the Parallel breakout board will use Mach 3 software, and USB will use Planet-CNC software.

Additional Information:
You can use this link to see the videos on how to connect the electronics together and make them work: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

Click the link to add information to this solution:
hey, where can i see the steps how can i control 3 or 4 step motor? can i use the Axis Electronics Combo? or i need to connect controller?

In our 3-Axis electronics kit, the power supply's provided are capable of both 110V-220V. You have the capability to switch between both in case you might decide to run 220v in the near future or will relocate where 110v is being used.

Additional Information:
Connect spindle to the board



Additional Information:



Additional Information:

Click the link to add information to this solution:
Does the power supply in the "3 Axis Electronics Combo (Small Motors)" have a 220V input option?

The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

Additional Information:


Additional Information:


Additional Information:
USB Motion controller breakout board work with planet cnc software?

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE BETWEEN PARALLEL AND USB ELECTRONICS COMBOS MOTOR KITS

To replace all of the electronics for a 4 axis system with all NEMA 34 motors, you will need the following components:

4 NEMA 34 stepper motors:
https://buildyourcnc.com/item/electronicsAndMotors-nema34-651ozin

4 drivers (one driver for each motor):
https://buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

One controller:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

24v Powers supply for the controller:
https://buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

2 48V power supplies for the motors and drivers:
https://buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-36v-48v

Click the link to add information to this solution:
i have a 4 axis cnc need to replace everything electronics and motor nema 34 what do i need to buy

Make sure all your bolts/screws are tighten correctly and if using a lead screw make sure your anti-backlash nut is not offset. Now a default setting will be 10101100 for your driver dip switch settings and in motor tuning (mach3) 1600 steps per, 400.02 velocity, 4 in acceleration. now the acceleration and velocity can be adjusted to move your machine faster, but if set to high they could stall. Make sure you have the correct wiring from your motor to your driver (https://www.buildyourcnc.com/Documents/PN.SM60HT86-2008BF-U%20(inhouse%20PN.60BYGH303-13)%20(1).pdf).

Click the link to add information to this solution:
I have your Nema 24 electronics kit and am having problems with the Z axis dropping over time. I am using a PC 8902 motor. Any ideas on what the problem is? What should be the motor tuning values in Mach3? Thanks

In our 3-Axis electronics kit, the power supply's provided are capable of both 110V-220V. You have the capability to switch between both in case you might decide to run 220v in the near future or will relocate where 110v is being used.

Additional Information:
Connect spindle to the board



Additional Information:



Additional Information:

Click the link to add information to this solution:
In the 3 Axis Electronics Combo, what is the AC input of the power supply (110v or 220v??). is it possible to specify a certain voltage when ordering?

These boards are compatible with Mach3 only at this time. We will be adding a Mach4 board in the near future.

Click the link to add information to this solution:
Are the 3 axis electronics combos with the Mach 3 USB breakout board compatible with Mach 4?

Did you connect the USB connector to the breakout board?

Additional Information:
YES I CONNECTED THE USB TO THE BREAKOUT BOARD

Click the link to add information to this solution:
I connected the electronics (for 2 x 4 feet) that I ordered from you. But how do I check if I connected all the wiring properly. There is neither any light on motor drivers nor on breakout board. And the motor shaft also does not move before and after the power supply is given.

What is the weight of the gantry, number of teeth on the drive sprocket and tooth pitch?

Click the link to add information to this solution:
I build a 3 axis router CNC the gantry is heavy in aluminium plate, witch plug n'play kit you suggest me 1 or two motor on the longest axis this will be drive with chain?

You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

Here is a list of the parts needed to get the electronics combo functioning (parallel or USB interface options):

- 22 or 24 gauge stranded hookup wire to connect all of the drivers to the USB or parallel interface (terminal to terminal connections),
- 18 gauge stranded hookup wire to connect the drivers to the power supply,
- a power cable (extension cord) to connect from the power outlet to the power supply,
- 4 conductor cable to connect the drivers to the stepper motors,
- a USB cable to connect from the computer to the USB interface (or for power to the parallel interface),
- for the parallel interface, a parallel cable is needed (male to male db-25),
- a computer (for parallel interface, the computer will need a parallel port and if the computer does not contain a parallel interface, the motherboard may have a header for it, or you can purchase a parallel adapter to plug into the motherboard, very inexpensive),
- cnc control software: for the USB interface, you will need planet-cnc software, for the parallel interface, you can use any industry standard cnc control software (the typical is Mach3 for Windows, or EMC2 or Linuxcnc for Linux (Linuxcnc.org).

5v power supply is not needed. The 5 volts signal level power is derived from the computer through USB on both types of interfaces.

Click the link to add information to this solution:
What else to I need to purchase along with the "3 Axis Electronics Combo w/ USB Interface Board" to get the electronics up and running? (software, 5V power supply, 4-conductor wire, etc.)

I have very detailed wiring videos for the Pokeys57CNC controller on the pokeys57CNC controller webpage: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[50] I purchased 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller (Mach3 and 4 Compatible) and Cable Pack I plan to use Mach 3 do You have a wiring diagram Thanks

Yes, I can furnish the redFly system without motors. You can request a quote for this at customerservice@buildlyourcnc.com

Click the link to add information to this solution:
[422] I'm interested in using Mach4 and already have 3 motors (425 oz-in). Is it possible to get a electronics system without the motors?

This version of the blueChick comes with the Parallel Breakout Board.

Click the link to add information to this solution:
Which electronics unit comes with item #230, the 3 axis USB or parallel? If parallel, do you have a package price that includes the USB electronics?

Our electronics contains a switchable power supply that allows you to switch the input mains voltage between 115 volts (110/120) and 230 volts (220/240). the hertx range is not specified, but there are capacitors to smooth out standard frequencies to enable DC output.

Click the link to add information to this solution:
hi, what about, if I buy from you some elecronic parts like (3 Axis Electronics Combo) and I use them here in france , where the electric voltage is 220V 50Hertz ? thats gonna works? thanks

The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

Additional Information:


Additional Information:


Additional Information:
USB Motion controller breakout board work with planet cnc software?

Click the link to add information to this solution:
what is the difference between parallel and USB electronics. I have a laptop that will run the mach3 program.