We carry several sizes of lead screw and stepper motors on our website, for example here https://buildyourcnc.com/Item/mechanical-leadscrews-lead-screw-!5-5-starts-10-tpi and here https://buildyourcnc.com/ProductSearchResults.aspx. Please call us at 281-815-7701 to discuss the particular lengths you would need and shipping options.

Additional Information:
https://buildyourcnc.com/ProductSearchResults.aspx is not working

Additional Information:



Additional Information:

Click the link to add information to this solution:
I have a project very similar to cnc machine. I need 3 lead screws of 1.8 m with all set (supports, bearings...etc). and 3 NEMA 42 motors that I can connect with. if those are available, I need the information about shipping to Oman or UAE.

Fusion 360 is a program that allows you to design in a parametric 3 dimensional environment and also provides a great CAM toolset. Fusion 360 will produce the gcode with the CAM capabilities. The gcode is used to move the machine in various ways in order to mill the material; however, software is needed to interpret this gcode and cause the machine to move according to the gcode instructions. This is called control software. So Fusion is CAD/CAM, and you still need "control". Mach3 is one example of control software for milling and is highly recommended.

Install Mach3 onto the computer that will connect to the redFly(CNC electronics), then configure the Mach3 parameters for the machine (motor tuning, plug-ins, inputs/output, etc.). Home the machine, load the gcode into Mach3 and the machine will move according to the gcode.

A word of caution, since you are new to CNC machines, make sure you familiar yourself with the machine and the movements of the machine specific to how the gcode is arranged with respect to the coordinates of the machine. Try with very simple gcode until you get a very good understanding of how the machine will move.

Click the link to add information to this solution:
Hello, My friend has purchased the Redfly and I am helping him a little with it. We are both very new to CNC. I am using fusion 360 at the moment. This can tool path and create gcode. I was wondering if Mach 3 or similar is still needed. Is there a tutorial you could point me to that explains how to get the Gcode from the PC, via Serial to the Redfly?

Hi, you can call me at the 281-815-7701 number. Please leave a message when you call as most of the calls are screened to avoid scam calls. You can also email me at customerservice@buildyourcnc.com or phooddaniel@berkeley.edu.

The newer kits that are featured on the home page include everything you need except a computer and software. The legacy CNC routers that are located in the CNC machines menu selection include all of the parts for the gantry, but you will need to build the table yourself. All of the information on the measurements to be followed for the table construction are on the machine pages.

Click the link to add information to this solution:
I am looking at getting a 4x8 cnc router kit. I am having a hard time figuring out what is included in the kit and what else i will need to buy with it to get off the ground and running. Is there someone i could talk to to walk me through it? If not, can you break down what all I need to go from scratch to a running set up? thanks

Unfortunately, end mills will dull over time and need to be sharpened or repurchased. We do not currently offer any sharpening service, but we have a large selection of end mills you can find here http://www.buildyourcnc.com/ProductsEndMills.aspx

Click the link to add information to this solution:
Hi, I got two different bits I use alot. The 1/16th and 1/32 end mills. I use them alot for making signs. They seem to be getting dull. They are very expensive so I was wondering can you sharpen these bits? Do you have a service to do this? Thank you

The greenBull kit (not the assembled) will need the table (the rails for the table is supplied), wires/cables for the stepper motors and stepper motor drivers, smaller gauge wires for digital wire connections (limit switches, drivers to control interface, etc), wires for the spindle connection to the VFD, tubing for water flow to and from the spindle, and a pump and reservoir (we are just about to introduce a small pump/reservoir/radiator/fan system for use with the spindle. The VFD/spindle, stepper motors/drivers and interface board are included.

Click the link to add information to this solution:
If I understand correctly, the greenBull kit comes with a spindle and laser. What else do I need to have a working machine. Obviously a table, do I also need the computer, software, wires, pump and plumbing, electronics, VFD, steppers and controllers?

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I have your Mach3 usb interface board and am interested in the relay board to turn plasma torch on/off. I have a different relay board that doesn't work, it needs 0/5v from output pin to trigger and the usb board doesn't put out 5 volts. Does this relay board need 5v on output or will work fine with this usb controller?

Hi, this BBB comes with a USB port and its cable to power it up. Once connected to the computer a led in the BBB will light up to show it has power.

Additional Information:
Breakout board I have does not have USB port for the 5v power. Does the parallel port supply the 5V power?

Click the link to add information to this solution:
Hi, I need assistance, the parallel breakout board I received looks different from the one on the video, does this one need a 5V supply? If so, where do I connect the positive and where do I connect the ground? Thanks for your help.

Are you trying to maintain sea level atmospheric pressure within this chamber, or are you just wanting to sense the pressure within the chamber at that altitude to determine how your product performs?

To respond, just enter another response on this page: https://buildyourcnc.com/FAQ/4675 and click on submit additional information.

Additional Information:
I would like to vary the pressure inside the chamber by using a vacuum pump, e.g. from 100kPa to 10kPa. It is to simulate the different altitude level. Then I will put my product in the chamber and test it at different pressure level.

Additional Information:
I would like to get a solution for designing this kind of chamber.

Additional Information:
Hi, can anyone advise on this?

Additional Information:
You can use our pressure sensor to dial-in the narrow range of vacuum that you need for your project. Build an air-tight enclosure/container that will contain the project components with some/one tube fittings at the exterior of the enclosure. The fitting(s) are needed to provide the vacuum within the container.

The pressure sensor will need to also sense the pressure within the container, so, either a fitting is needed on the container, or in-line with the vacuum hose will need to be provided. You will also need a check valve in-line with the vacuum line between the pump and the container (before the pressure sensor fitting) so there will be no air escaping through the pump when the pump is not running.

All of the components can be found here:
https://buildyourcnc.com/category/pneumatic-hydraulic

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I am designing an altitude chamber to test the performance of my product at different altitude level up to 20k feet of height. My chamber dimensions are 1m x 1m x 1m. Can you propose a solution? E.g. vacuum pump model, pump controller, valve, etc.

All of our CNC machines can cut melamine. If your application (kitchen doors) requires large cutting area, then I would recommend the following machines:

- greenBull 4x (4'x8'), 5x (5'x10') or 6x (6'x 12')

- greenLean 4'x8' vertically oriented CNC machine

- Or our Fabricator Pro 4'x8' metal CNC machine

Click the link to add information to this solution:
Can you recommend which CNC machine to go with for cutting melamine and making kitchen doors from MDF. Also do you provide training on operating and setting up machine for shop production use? Thanks

Yes, the Mach3 USB board has two terminals that require 24V connection. Most VFDs have a 24V output that can be used to power this part of the Mach3 USB board.

The V+ and V- on the Mach3 USB is not absolutely necessary to operate the CNC machine/router. The V+ and V- of the Mach3 USB board powers the outputs, inputs, and spindle's speed and control.

Here is the Mach3 USB link for more information:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

The new YL600 VFD we have in stock may not have this 24V output. There is a 12V terminal, but I have not tested that terminal if it outputs 12V, or if it is a 12V input. If you are only conecting limit switches to the Mach3 USB and need to power that portion, 12V will be sufficient.

I will delve into these aspects in far more detail on video.

Thanks and Merry Christmas to you as well!

Click the link to add information to this solution:
Hey Guys, I have a brand new redleaf and 5x. In the final stages of wiring and wondering a few things. Can I connect the Mach3 USB board V+ V- to my frequency inverter (type YL600-2s-2k20)? If so where? Will your upcoming (part 2)video deal with this as well as final connections for limit switches and stop button? Merry Christmas!

Yes, we can help you with leveling your CNC machine even if you didn't purchase it from us.

Click the link to add information to this solution:
[789] I need to level my cnc machine, but I didn't purchase it from you, so: Do you offer tech support with leveling a cnc? Because I don't see this problem listed .And: Do you offer support if my machine was purchased in China or from another vendor?

The mxl 0.08" pitch is fine for moving the weight of a gantry that contains a 40 watt laser tube and optics. I would not advise this timing belt for CNC applications that need to move heavy items such as spindles, routers, and heavier structures that are required to move these spindles and routers around.

The mxl 0.08" pitch timing belt is also great for 3d printers.

Click the link to add information to this solution:
Originally bought the Blacktooth Laser kit, but the upgraded laser tube size and needed a larger casing. With that I need to upgrade the belts to a 36" run. Can you advise whether the mxl.08" timing belt is sufficent or do I need the .2"in.

Polabs prepared step by step user guide for PoKeys57CNC and Mach4 to try answering such questions. It is available in our downloads section: https://www.poscope.com/wp-content/uploads/downloads/Pokeys/LibrariesAndPlugins/Mach4 and PoKeys57CNC - step by step guide.pdf

Click the link to add information to this solution:
I need your assistance... I have two items left to setup on my Pokey57CNC and Mach4, Home switches and Spindle Speed. I have watched the videos, but they are for Mach3 and the screens are different in Mach4. Can someone please explain the setup of these two items in Mach4?

Youmay be able to find an adapter for your cable, or even a new cable, locally. This is the cable we sell that will work, https://www.buildyourcnc.com/item/electronicsAndMotors-cable-wire-db25-male-male

Click the link to add information to this solution:
The female 25 pin socket on my computer has to be connected to a similar socket on the breakout (parallel) board which came with my Blacktooth. Do I need a DB25 to DB25 cable, if such a thing exists? The cable I have is male to female.

Here is how to connect your router to the parallel breakout board through the on-board relay. You will need a spare extension cord. You will need to remove a portion of the outer jacket of the extension cord to expose the white, black and green wires (white = neutral, black = live and green = ground), understanding that the neutral and live create the completed circuit.

See this image of a similar connection. The terminal has the same connections.
https://www.buildyourcnc.com/images/vacuum-pressure-controller-relay-terminals-700.JPG

Image of the relay terminal:
https://www.buildyourcnc.com/images/breakoutboardrelayNONC.PNG

The live/black wire would be cut and one end of the cut would be secured into the P terminal and the other cut end would be secured into the S terminal. The live and ground wire would be uncut and travel from the plug to the router.


Additional Information:
You can also connect other high powered devices to the breakout board using any of the output terminals. You will need to supply extra relays like the one shown here:
https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Or you can find SSRs (Solid State Relays) that will accept 5v to drive the relay coil. Make sure the SSR will protect the 5V line from Back EMF as there is a coil in the relay. The one we sell contains a fly-back diode to protect the 5v terminal.

Click the link to add information to this solution:
I have your breakout board with relay parallel port , I have a vacuum, light on router and air pump I want to also hook up to board, can I hook those up to board and also could I had reylays to each one, what is the best way to figure this out any information would be great. Thanks

All of our CNC machines can cut melamine. If your application (kitchen doors) requires large cutting area, then I would recommend the following machines:

- greenBull 4x (4'x8'), 5x (5'x10') or 6x (6'x 12')

- greenLean 4'x8' vertically oriented CNC machine

- Or our Fabricator Pro 4'x8' metal CNC machine

Click the link to add information to this solution:
CAN YOU RECOMMEND WHICH CNC MACHINE TO GO WITH FOR CUTTING MELAMINE AND MAKING KITCHEN DOORS FROM MDF. ALSO DO PROVIDE TRAINING ON OPERATING SETTING UP SHOP PRODUCTION USE? THANKS

This would totally work for that application. This cable carrier is used for any object that needs to move and carries some electrical or tubing within it. This cable carrier is great for cable management where you want to make sure the wires and tubes are in a position that you set, not where the wires and tubing want to go.

Click the link to add information to this solution:
[311] I am looking to use this type of thing with a pipe for theater. Where the pipe can be lowered and it would have electrical and signal cable inside. Is this good for that or should I look at something else?