https://buildyourcnc.com/Item/electronicsAndMotors-electronic-component-e-stop-button-switch-safety#prettyPhoto/0/

Click the link to add information to this solution:
How do I wire up multiple E-stop to breakout board, does each E-stop need there own pin? If not since there are only 4 screws on stop 2 for no and 2 for nc do you just splice the wires together if your only using 1 pin? Thanks

Red is A+
Blue is A-
Black is B+
and Green is B-

Click the link to add information to this solution:
I purchased the 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller and the motors supplied only have 4 wires coming out of them (R,G,B,Blk). Your wiring video shows wiring 8 cables. do you have a video showing how to wire the 4 wire version?

The E.Lu.5 Error code on your VFD is related to Low Voltage.

The recommended action is:
- 1. Check whether the input voltage is normal. (the voltage from the wall/breaker to the VFD)
- 2. Check whether there is a sudden change in load.
- 3. Check whether there is any phase missing.

Unfortunately, these three recommended actions will probable require an electrician to test the line going into the VFD.

Additional Information:

Click the link to add information to this solution:
I have wired up my 110v VFD and my 2.2Kw spindle and I get an E.Lu.5 code. My wiring is correct and the parameters are set to those for the VFD according to your website I found in a previously answered question from someone here. Any help would be greatly appreciated, thank you!!

Since the pump will use a standard 12v power supply, you will have two wires. One of those wires will be connected from the power supply to the pump. The other wire will be connected to the power supply and the pump, but cut that wire and connect one side of it in the P terminal and the other end in the S or the O terminal depending on if you need the connection as NO (Normally Open) or NC (Normally Closed).

Step number 9 in the instruction will have the relay connection information:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
I wpold like to know how to hook up my water pump (12vdc 9 amp) to turn it on and off using Mach 3. I have your Blue Brew break-out board Rev. 2.8 dated 8-12. Explain how the three relay connections work for this application? Thanks.

The formula for finding the steps per mm is found in the units itself. First, you mentioned that the motor is a servo. This needs to be clarified as a servo is different than a stepper motor. Some servos behave similar to a stepper motor, so I will continue with this in mind.

The formula is (steps/mm):

You need to find the steps. The stepper motor has a natural number of steps per a full revolution. This is typically 200 steps per revolution.

The driver for the stepper motor allows you to increase the number of steps per revolution by adding a specified number of steps between each step. For instance, if you set the driver to 1/4 microstepping, then instead of having 200 steps per revolution, you would have 200 x 4 = 800 steps per revolution.

So now we have the first part of the formula:

Steps / mm = (200 x 4) / mm

Lets determine the mm side of the formula:

You mention that the pitch is 0.5 mm. Check to insure that the lead is also 0.5 mm. This could be a multiple start lead screw where the pitch is different than the turns per mm. If in this case, that the 0.5 mm is the travel for one full revolution, then you can simply plug this into the formula as:

mm = .5 mm

Otherwise, determine how fat the travel is for one complete revolution.

Therefor, with what we know and the driver is set at 1/4 microstepping and the stepper motor has a natural step count per revolution at 200:

steps / mm = (200 steps x 4) / 0.5 mm = 800 steps / 0.5 mm = 1600 steps / mm

If your travel for one revolution is not 0.5 mm, then plug in your travel distance instead.



Additional Information:
i know about steps/mm calculation for stepper motor, because i am using servo motor that why i asked about that. please tell for servo motor.

Additional Information:
because its my first time with servo motor i have no idea about calculation of parameter with servo.

Additional Information:
Have you attempted to contact the manufacturer or seller of the servo? We typically respond to customers of our products on this customer service area, unless we have extensive knowledge of the subject and can answer the question efficiently.

Additional Information:

Click the link to add information to this solution:
hello there, i am using servo motor for my X and Y Axis but i dont know how to calculate steps/mm for that, the lead screw i am using is have pitch of .5 mm. please helpme on this i have done everything only this point is pending.

Sure, let me check.

Additional Information:
Your order was shipped out on Tuesday (10/20/2020). I noticed that your email was not stored in the customer record when the order was made. I will send you the tracking number via email now.

Click the link to add information to this solution:
Placed an order for the cable set for the Pokeys57cnc interface on 10/20 but it is not showing up in My Account as being ordered. It was charged to my credit card and I have not had any info that it was received by you.

I have very detailed wiring videos for the Pokeys57CNC controller on the pokeys57CNC controller webpage: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[50] I purchased 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller (Mach3 and 4 Compatible) and Cable Pack I plan to use Mach 3 do You have a wiring diagram Thanks

I just sent you the commercial invoice via email. Thanks.

Click the link to add information to this solution:
Could you please e-mail us the invoice for the order, shipment is currently at the customs and your invoice is needed so it can be cleared. As I can't seem to find any order number or other reference in your system, the only reference I have is the tracking number LZ676176940US and the order date is 12/26/2017. Thanks!

Make sure all your bolts/screws are tighten correctly and if using a lead screw make sure your anti-backlash nut is not offset. Now a default setting will be 10101100 for your driver dip switch settings and in motor tuning (mach3) 1600 steps per, 400.02 velocity, 4 in acceleration. now the acceleration and velocity can be adjusted to move your machine faster, but if set to high they could stall. Make sure you have the correct wiring from your motor to your driver (https://www.buildyourcnc.com/Documents/PN.SM60HT86-2008BF-U%20(inhouse%20PN.60BYGH303-13)%20(1).pdf).

Click the link to add information to this solution:
I have your Nema 24 electronics kit and am having problems with the Z axis dropping over time. I am using a PC 8902 motor. Any ideas on what the problem is? What should be the motor tuning values in Mach3? Thanks

We apologize for the confusion! The current greenBull kit in the video is a 4' x 8' gB CNC machine, so we currently have a shorter Y-axis length, compared to the 5X/6X kits. However with the gB 5X you should skip every other section(or something similar so it is symmetrical), since we added the option for you to increase the number of ribs if you wish, but is not necessary for the CNC machine.

Click the link to add information to this solution:
Building the 5x10 GreenBull, I went to install the ribs on the mid section of the gantry and you say in the video to skip a spot for the motor to sit, but I have 3 sections that are going to blank not just one like you show in the video. Do I skip more than one, am I missing ribs?

Hi, this BBB comes with a USB port and its cable to power it up. Once connected to the computer a led in the BBB will light up to show it has power.

Additional Information:
Breakout board I have does not have USB port for the 5v power. Does the parallel port supply the 5V power?

Click the link to add information to this solution:
Hello, we are trying to assemble a kit and the breakout board rev 2.1 that we have does not match the video... we do not see where to connect the 5v powersource to finish step #3, can you provide a location for the power hookup for our board.

You can ask the question on this customer Service section. The questions on this section get answered immediately, or faster than our email service.

Click the link to add information to this solution:
I have received an email from you re my question Number 13956 and I want to make some inquiries re just the control board could you send me a email address as using the address that the email was sent to me keeps coming back.

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

Are you connecting this spindle and pokeys57cnc controller to a CNC? or are you simply wanting to control a spindle by itself?

Additional Information:
Sorry, I thought that my question made it clear that it is for a Chinese 40W laser and I am replacing the original board in it with the 57cnc and I’m told that I need to buy stepper drivers and probably the stepper motors as well and I was asking which drivers and motors would be most suitable for me to buy to go with my already purchased from here 57cnc board

Additional Information:
Ps, I intend to use Auggie from Gearotics to drive the laser

Click the link to add information to this solution:
I have a Chinese 40w laser that I was advised to get a pokeys57cnc for which I did. I didn’t realise that I would need stepper drivers for so was wondering which you would recommend as well as which stepper motors as I may as well replace those as well. Any advice is gratefully received, thanks

That will depend on the controller that was installed in the redFly. If the controller is a pokeys57CNC controller, you can use Mach 4 with that system.

You can add a 4th axis and an ATC (Automatic Tool Changer) with the redFly system.

Click the link to add information to this solution:
Does the Redfly that I bought with the GreenBull in 2016 work with Mach4? Also I want to add a 4th axis and a spindle with automatic tool changer. Will this work too or do I need a new control board? I bought my CNC with a longer Z travel, so I have plenty of room for these. Thanks!

This is most likely a wiring issue. I would disconnect all of the power to the drivers and reconnect one at a time to isolate the problem.

Additional Information:
that was not helpful. I already did that way before submitting this question. there are not that many wires here and I have already rewired this a few times. I actually think its a software or interface board issue because it does work sometimes but then trips (possibly a amperage / voltage issue) I am using the interface board that has a parallel port and usb for 5V. are there different settings that I need to setup?

Click the link to add information to this solution:
I'm using the big 651oz in stepper motor for X and Y and the smaller 325 for the z and X and Y keep tripping when I try to tune the motors on Mach3 but Z seems to work. I have to turn power on and off to reset....is this a wiring issue?

If one or more motor is not responding, please follow the troubleshooting directions below:

For parallel Bob only! Make sure both the parallel and USB are connected.

Re-check wiring, and connections for continuity (no breaks in the wires) and check for correct wiring locations from driver to BoB.
Check dip switch settings on the driver.
Check components, by swapping the motors (ex. y-axis motor to z or x-axis driver and z or x-axis motor to y-axis driver) to check if motor functions on another driver.
Depending on software check step low active (mach 3) or invert pulse (planet-cnc) for the axis which is not responding.
Mach 3 - config/port & pins/motor outputs / Planet-CNC - file/settings/axes

Click the link to add information to this solution:
I have an engine NEMA 34 from Y axis on my green bull that do not response, I already check connections and everything seems to be OK, how can I check that the motor it's working properly or not?

Your question caused me to make a quick video to understand how the pokeys57CNC controller works with a THC.

Click the link to add information to this solution:
[596] Would you help with the Hook up and the Configuration and whether it is in the Plugin or mach 4 control configuration that needs to be set. I decided to use the ultra fast encoders connector pin #8, 12 and 13 for Arc ok, UP and Down. Please advise what setting to set to make it all work. Thank you very much for your help!