Sell you liner guideways and screwballs to 2000 mm. (78 inches) length?

Question #: 2333

Question: Sell you liner guideways and screwballs to 2000 mm. (78 inches) length?

Current Solution

We sell our lead screws at length but the longest single length is 78" for our 1/2" and our 3/8" is 72" long, now for our linear guide rails the longest rail we have (new item) is 55" at the moment we will be getting longer rails in the near future.

Respond:

Other Possible Solutions to this Question

DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?
We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.
Click the link to add information to this solution:
DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?
DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?
We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.
Click the link to add information to this solution:
DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?
WHAT ARE THE BLACKTOOTH LENS SIZES AND FOCAL LENGTH SPECIFICATIONS?
The lens is 20mm wide and a 50.6mm focal length (the one included). This lens will stand up to at least 30PSI air assist.

The mirrors are 25mm wide mirrors.

Focal length is the distance from the lens to the material for the laser converge into the best focal point. If a lens is listed as 2". You measure 2" from the lens to the material, this will be the tightest point the laser can go before it starts to re-expand again losing focus.
Click the link to add information to this solution:
WHAT ARE THE BLACKTOOTH LENS SIZES AND FOCAL LENGTH SPECIFICATIONS?
I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?
We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V
Click the link to add information to this solution:
I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?
DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?
The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

Additional Information:
Click the link to add information to this solution:
DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?
WHAT IS LASER AND LENS FOCAL LENGTH?
The lens is 20mm wide and a 50.6mm focal length (the one included). This lens will stand up to at least 30PSI air assist.

The mirrors are 25mm wide mirrors.

Focal length is the distance from the lens to the material for the laser converge into the best focal point. If a lens is listed as 2". You measure 2" from the lens to the material, this will be the tightest point the laser can go before it starts to re-expand again losing focus.
Click the link to add information to this solution:
WHAT IS LASER AND LENS FOCAL LENGTH?
DO YOU GUYS SELL THE POTENTIOMETER FOR YOUR LASER SYSTEM BY ITSELF
Yes, it is found in laser components section
Click the link to add information to this solution:
DO YOU GUYS SELL THE POTENTIOMETER FOR YOUR LASER SYSTEM BY ITSELF
I need a guide rail 15mm X 100mm yours is 2000mm or 2 meter, do we cut the rail to size? do you sell the block separetly?
We sell HIWIN rail and Linear guide rail by the inch (cut to size) as well as the blocks individually.
Click the link to add information to this solution:
I need a guide rail 15mm X 100mm yours is 2000mm or 2 meter, do we cut the rail to size? do you sell the block separetly?
wHAT IS THE SMALLEST LENGTH SHAFT I CAN USE FOR YOUR #25 DRIVE SPROCET?
The hub length of the drive sprocket and the other mechanical devise that is used to connect on the shaft will determine the length of the shaft needed for use with the drive sprocket.

The hub lengths for our drive sprockets are 1/2". So if you are connecting the drive sprocket to a motor, your motor shaft will need to be at least 1/2" in length.
Click the link to add information to this solution:
wHAT IS THE SMALLEST LENGTH SHAFT I CAN USE FOR YOUR #25 DRIVE SPROCET?
WHAT LENGTH OF MOTOR CABLE SHOULD BE USED WTIH THE BLUECHICK V4.2
The recommended total length of motor cable should be 15 feet for the blueChick v4.2

Z - 6 feet
Y - 5 feet
X- 4 feet

20 AWG 4 conductor

If your drivers will be positioned farther from the machine, you may need longer cable.

Additional Information:
Click the link to add information to this solution:
WHAT LENGTH OF MOTOR CABLE SHOULD BE USED WTIH THE BLUECHICK V4.2
When will the 2000 mm HIWIN Spec Linear Guide rail be available?
That is difficult to tell at this time. Right when we get them in, they go fast. These items come from China and the units are shipped in via freight on ship, so there are many factors on the delivery such as weather.
Click the link to add information to this solution:
When will the 2000 mm HIWIN Spec Linear Guide rail be available?
IS THE "#25 ROLLER CHAIN" ADJUSTABLE TO ANY LENGTH? LIKE IF I ORDERED TEN FEET OF IT, CAN MAKE TWO 3-FOOT LOOPS AND ONE 4-FOOT LOOP USING SOME SORT CHAIN JOINER?
Roller chain in general is adjustable by using "master links", which are links which have horseshoe clip holding the pin and thus allow connections to be made or broken. The #25 is a designation of the type of roller chain. ANSI codes designate that the first digit(s) specify the pitch in eights of an inch, and the last digit is 0 for standard chain, 1 for lightweight chain, and 5 for bushed chain with no rollers. So #25 is 2/8 = 1/4 inch pitch bushed chain with no rollers.
Click the link to add information to this solution:
IS THE "#25 ROLLER CHAIN" ADJUSTABLE TO ANY LENGTH? LIKE IF I ORDERED TEN FEET OF IT, CAN MAKE TWO 3-FOOT LOOPS AND ONE 4-FOOT LOOP USING SOME SORT CHAIN JOINER?
HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE
The motor that is attached to the 4th axis is wired as follows:

The motor should have red, green yellow and blue wires coming form the motor. The red and green are paired as one coil and the yellow and blue is paired as the other coil. You can wire the motor to a 3.0 amp driver with red to A+, green to A-, Yellow to B+ and Blue to B-
Click the link to add information to this solution:
HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE
WHAT CAUSES RINGING IN YOUR EAR AND HOW CAN YOU STOP IT?
Tinnitus . Learn to love it. No really you should see a doctor. Make sure. White noise will help you sleep when it gets loud.

Additional Information:
I learned, too late, that if a sudden loud event causes tinnitus, see an audiologist IMMEDIATELY. They can do something about it if addressed within a day or so.

Wear hearing protection...always. Loud noises trigger my tinnitus, and headphones and ear plugs (when out & about or at the movies, subway, etc) help tremendously. Mine are rated 33dB.
Click the link to add information to this solution:
WHAT CAUSES RINGING IN YOUR EAR AND HOW CAN YOU STOP IT?
BUILDING ONE OF YOUR GREENBULL 6X LONG AND 2.2 KILOWATT SPINDLE DOES NOT FIT. SEEMS LEAD SCREW YOU SENT WITH KIT IS SHORT 42" LOOKS LIKE IT NEEDS TO BE 5 OR 6 INCH LONGER. THIS CORRECT? WHAT THE NEEDED LENGTH FOR UNIT?
The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:
Click the link to add information to this solution:
BUILDING ONE OF YOUR GREENBULL 6X LONG AND 2.2 KILOWATT SPINDLE DOES NOT FIT. SEEMS LEAD SCREW YOU SENT WITH KIT IS SHORT 42" LOOKS LIKE IT NEEDS TO BE 5 OR 6 INCH LONGER. THIS CORRECT? WHAT THE NEEDED LENGTH FOR UNIT?
IS THERE A WAY TO GET RID OF THE PARALLEL CABLE AND SOMEHOW USE USB ?
If you select the Settings Page and select or tick Auto Limit Override - this will allow you to back off the switch.

Additional Information:
limit and home switch
Click the link to add information to this solution:
IS THERE A WAY TO GET RID OF THE PARALLEL CABLE AND SOMEHOW USE USB ?
CAN YOU PLEASE TELL ME THE AVAILABILITY OF 12X36 BLUE CHICK 4.2, AND COST FOR SHIPPING TO ZIP 72802 IN RUSSELLVILLE, ARKANSAS?
Yes, the blueChick kits are available. You can get the shipping rates automatically in the shopping cart. There will be a calculate shipping button on the enter shipping information section of the shopping cart.
Click the link to add information to this solution:
CAN YOU PLEASE TELL ME THE AVAILABILITY OF 12X36 BLUE CHICK 4.2, AND COST FOR SHIPPING TO ZIP 72802 IN RUSSELLVILLE, ARKANSAS?
IF YOU HAVE CIRCUIT (OR PICTURE) OF HOW THIS RELAY IS CONNECTED TO THE ROUTER
Check step 9 on this page: http://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay
Click the link to add information to this solution:
IF YOU HAVE CIRCUIT (OR PICTURE) OF HOW THIS RELAY IS CONNECTED TO THE ROUTER
WHAT LENGTH OF CABLE DO I NEED FOR A BLAKCFOOT
The blackfoot requires a total of 50 feet of cable.

The X axis needs 15 feet
The Y axis needs 17 feet
and the Z-axis needs 18 feet

These are 20 gauge 4 conductor cable.

Additional Information:
Click the link to add information to this solution:
WHAT LENGTH OF CABLE DO I NEED FOR A BLAKCFOOT