Yes, we can provide a laser attachment for the long Z version of the greenBull 4x, 5x and 6x. Please call us to get more information and pricing for the laser attachment.

Click the link to add information to this solution:
I have a greenbull 5x with the long Z. Is there a laser kit that I can get for that model?

I would recommend using the blackToe CNC machine kit. The overall travel dimensions are 24" x 48" x 6". This will provide a bit of space on the sides as wiggle room if your guitar bodies are at the extremes of the 12". Also, if you are manufacturing may of these, the larger routing area, the more guitar bodies you will be able to cut at one time.

Click the link to add information to this solution:
I need a machine to cut guitar bodies. The bodies are 12" x 16" and 1.5" thick. What would work best?

You will need the following:
- router/spindle for the machine
- computer to control the machine
- construct a table if the optional table is not purchased
- wire and cable to connect all of the electronics

Additional Information:
- software to run the gcode (purchased separately)

Click the link to add information to this solution:
DOES THE PRICE OF 2’ X 4’ ROUTER INCLUDE EVERYTHING WOULD NEED TO START ROUTING?

For the NEMA 34 stepper motor with a maximum current of 6 amps, 18 AWG wire would technically be sufficient. According to the American Wire Gauge (AWG) standard, 18 AWG wire can handle up to around 10 amps of current in chassis wiring and around 16 amps in power transmission. If you are considering running a very long length of cable from the driver to the stepper motor, you may want to consider using 16 AWG.

As for the spindle, this wire gauge is well-suited. There are three phase shifts, each at 120 degrees and each conductor is carrying only 1/3 of the power. At 220v, 2200 watts / 220 V = 10 amps. 1/3 of 10 amps is 3.333 amps, so each conductor will be have a load of 3.33 amps.

Click the link to add information to this solution:
[801] Is this enough rating for a Nema 34 motor with max 6 amps? Also what about a 220V 2200Watt Spindle?

Yes, it is feasible to create a machine with a cutting area of 13'x15'. Your mechanical and structural systems will need to be able to span a bit more than the 13' if that will be the axis travel along the gantry.

We have not cut carpet with our lasers, but I don't see why not. With that said, be extremely careful with the materials in the rug. Read the MSDS (Material Safety Data Sheet) for the rug you intend to cut as some materials will emit corrosive and harmful gases and chemicals when lased.

Click the link to add information to this solution:
Hi I want to build a cnc laser table 13'x15' cuttting area. Is this feasible. Also would the 80watt laser be enough power to cut through carpet

I haven't delved into using encoders with stepping motors too much. From my research, you need to have a controller that can provide the closed loop control, rather than software handling that process. I have also found from my research that using encoders on stepping motors is generally used to stop the machine in the case that the motor failed to achieve the commanded position for some reason and gives the user the chance to correct and continue with the job.

If you want proper closed loop control, it may be best to go with servos and servo controller that provide the closed loop control within the real of those two components.

Click the link to add information to this solution:
I HAVE NOT SEEN ANY REFERENCES TO ENCODER FEED-BACK CAPABILITY IN OF THE HARDWARE YOU SELL. THIS A SUPPORTED FEATURE WITH HARDWARE/SOFTWARE SELL?

A couple of things you can try to reduce the noise of a motor.

First, change the amp setting on the driver to a lower value. This will make the initial thump lighter, and cause the motor to run quieter, but the torque may not be as high as desired.

Second, increase the micro stepping to a higher value, like 1/16 (3200) instead of 1/8 (1600), for instance.

Click the link to add information to this solution:
My X axis motor runs normally at a jog rate or 2-10% , but makes a loud noise at any higher jog rate

These files are no longer available. We suggest purchasing a kit, like the blackToe, or blackFoot as these kits are far more rigid and perform much better.

https://www.buildyourcnc.com/blackToe2x4v40.aspx

https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4

Additional Information:
20

Additional Information:

Click the link to add information to this solution:
Would you be able to provide .DWG/.DXF files instead of .NC files for the CNC Routing Machine Kit Version 1.3 please?

Yes Mach3 is a great program. Our 3 axis is 6'X12'X3'using all BYCNC components (incl. redsprout)

Click the link to add information to this solution:
I JUST BOUGHT THE 3 AXIS W/HEAVY GANTRY, WILL MACH 4 RUN WELL WITH THIS, AND HOW LARGE CAN GO CUT AREA

This is most likely a wiring issue. I would disconnect all of the power to the drivers and reconnect one at a time to isolate the problem.

Additional Information:
that was not helpful. I already did that way before submitting this question. there are not that many wires here and I have already rewired this a few times. I actually think its a software or interface board issue because it does work sometimes but then trips (possibly a amperage / voltage issue) I am using the interface board that has a parallel port and usb for 5V. are there different settings that I need to setup?

Click the link to add information to this solution:
I'm using the big 651oz in stepper motor for X and Y and the smaller 325 for the z and X and Y keep tripping when I try to tune the motors on Mach3 but Z seems to work. I have to turn power on and off to reset....is this a wiring issue?

If you purchase the Vertical Laser XL in kit form, then we would be able to deliver it within 2 weeks. If you want the Vertical Laser XL to be assembled, we would need a minimum of 1 month.

Additional Information:
What is the shipping cost to rural WV? Mannington, WV.

Click the link to add information to this solution:
Hello! How fast could I get a VLXL? Looking to get it by the end of the month. In WV. Ben

Yes, this 4th axis system will work with the Masso controller. The 4th axis has a standard stepper motor. You will need a driver between the Masso controller and the stepper motor.

Click the link to add information to this solution:
[410] Will this work with the OneFinity Elite series with the MASSO controller?

Depending if the spindle can work with this specific VFD, it might be possible. However we would not like to risk you working unit, with a possible match so we would like more details on your specific model and any information available on the spindle itself.

Response
The only info on the spindle is 2.2KW 400HZ 220V. Made by Zhong Hua Jiang.

Was originally on a Delta C200 vfd. That is 220 single phase.

Click the link to add information to this solution:
I PURCHASED A VFD AND SPINDLE FROM FRIEND, HIS SET UP IS 220. DON'T HAVE 220 IN MY SHOP. QUESTION CAN USE YOUR 110 WITH THIS SPINDLE??

Yes, if you need a replacement part on your machine please call us at 281-815-7701.

Click the link to add information to this solution:
I have a blacktooth laser engraver. The Y Axis stepper motor needs to be replaced. Can you please provide me with the information I would need to replace this motor.

The torque curve for the 651 oz-in stepping motor can be found here:

https://www.buildyourcnc.com/item/electronicsAndMotors-nema34-651ozin#prettyPhoto

Click the link to add information to this solution:
Using your NEMA 24 stepping motor with microstepping, can I get a speed range from 3 RPM to 600 RPM ?

You can determine if the area is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

Click the link to add information to this solution:
WAS WONDERING IF YOU COULD TELL ME WHETHER OR NOT SHIP ANY OF YOUR KIT PRODUCTS TO THE UK?

a motor stop working and get very hot

Click the link to add information to this solution:
I'm using Vectric's Aspire for design on my ShopBot. Do you know which output format I need to generate for the LeanGreen?

Are you asking if you can change the X and Y axes? Please clarify.

Additional Information:
Yes i wanna chains the x with the y axes can i make this with the software ?????

Click the link to add information to this solution:
i wanna chains the X with the Y assis how can i do this

The term cGy (centigray) is a unit of absorbed dose of ionizing radiation such as x rays or gamma rays. Cell phones do not emit ionizing radiation. They emit nonionizing radiation, namely radiofrequency (RF) energy. Absorption of nonionizing radiation in the body is measured in terms of the specific absorption rate (SAR) in units of watts per kilogram. Both ionizing and nonionizing radiation are forms of electromagnetic energy. The difference is that ionizing radiation has sufficient energy per photon to cause ionization of molecules. Nonionizing radiation does not. It is the ionizing effect of ionizing radiation that has been linked to increased risk of cancer. For more information on cell phones and health check out a Medical College of Wisconsin website. For more information on ionizing versus nonionizing radiation check out a University of Michigan website. Gary Zeman, ScD, CHP Lawrence Berkeley National Laboratory

Click the link to add information to this solution:
MY QUESTION THAT KNOW CANCER CAN BE CAUSED WHEN OUR BODY EXPOSED TO DOSES OF 50 CGY OR HIGHER. WHAT DOES STAND FOR? DO EMIT?