[ Log In ]
[ Register ]

Question #: 13773

Question: What are the other two dimensions of the 1/2" ID bearings used to support lead screws?

Current Solution

Inside Diameter: 1/2" (actual dimension 0.4975 inches or 12.63 mm)

- Outside Diameter: 1.122 inches or 28.4988 mm

- Thickness: .31 inches or 7.89 mm

Thank you for this question as it caused me to update the description:
https://www.buildyourcnc.com/item/bearing-!5-standardbearing

Respond:

Other Possible Solutions to this Question

  • what are the dimensions and model number of the 3/8" ID roller bearings on your website?

    The specifications for our 3/8" bearings are R6ZZ. The ZZ means double metal shielded. The metal shielding is to protect the ball bearings between the inner race and outer race.

    Inside diameter: 3/8"
    Outside Diameter: 7/8"
    Width: 9/32"

    Click the link to add information to this solution:
    what are the dimensions and model number of the 3/8" ID roller bearings on your website?

  • What are the mounting hole dimensions of the 1/2" Anti-Backlash Lead Nut

    The mounting hole dimension for the 1/2" 10 TPI 5 starts antibacklash nut is 1.13" or 28.7 mm. I added a drawing to the antibacklash nut product webpage so you can see other dimensions.

    Antibacklash nut product webpage: https://www.buildyourcnc.com/item/mechanical-leadscrews-antibacklash-nut-!5-5-starts-10-tpi

    Thanks

    Additional Information:
    You can also see the drawing directly here: https://www.buildyourcnc.com/images/Antibacklash_nut_1_2_drawing-800.JPG

    Click the link to add information to this solution:
    What are the mounting hole dimensions of the 1/2" Anti-Backlash Lead Nut

  • What are the actual measurements of the 5/8 and 1/2 ID bearings?

    The dimensions for each bearing (5/8" and 1/2"):
    1/2": OD 1.1255" - 28.5877mm / height 0.3150" - 8.001mm

    5/8": OD 1.3750" - 34.925mm / height 0.3440" - 8.7376mm

    Click the link to add information to this solution:
    What are the actual measurements of the 5/8 and 1/2 ID bearings?

  • Hi, I need the lead screw and bearings for x/y/z axis of the CNC. What is the length of "1/2" Lead Screw per inch (Steel)"?

    Depending on the size of your CNC machine, it will vary the length required for your application.
    Please verify the CNC machine, and we can go into detail on the specific lengths or methods for the linear guide mechanics.

    We sell our ACME Screw (1/2" per inch), also our longest length of ACME Screw is 76-3/4".

    Click the link to add information to this solution:
    Hi, I need the lead screw and bearings for x/y/z axis of the CNC. What is the length of "1/2" Lead Screw per inch (Steel)"?

  • WHAT ARE THE SHIPPING DIMENSIONS FOR VERTICAL LASER

    Shipping crate size 121" X 36" X 92"

    Weight 511 LBS

    Click the link to add information to this solution:
    WHAT ARE THE SHIPPING DIMENSIONS FOR VERTICAL LASER

  • WHAT ARE THE SHIPPING DIMENSIONS FOR GREENBULL?

    76" X 40" X 26"
    230 LBS

    Click the link to add information to this solution:
    WHAT ARE THE SHIPPING DIMENSIONS FOR GREENBULL?

  • WHAT ARE THE BLACKTOOTH SHIPPING DIMENSIONS?

    The blacktooth ships in 3 boxes.

    Structure 38x22x5 #54

    Components 14x13x13 #30

    Laser Tube 35x7x6 #4

    Click the link to add information to this solution:
    WHAT ARE THE BLACKTOOTH SHIPPING DIMENSIONS?

  • WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

    Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
    To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
    The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
    Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.


    Link:
    https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

    Click the link to add information to this solution:
    WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

  • I just changed my X and Y to the ACME 1/2" 5 start lead screw. What are the motor tuning numbers. I have the book built machine.

    The settings that will have to be change will be your steps per inch in motor tuning (mach 3), or settings/axes(planetCNC). But we do not have the actual numbers/specs that will fit your 10 TPI 5 start lead screw, here is a tutorial video which explains how to get the exact numbers you need! (

    )

    Click the link to add information to this solution:
    I just changed my X and Y to the ACME 1/2" 5 start lead screw. What are the motor tuning numbers. I have the book built machine.

  • If I buy the 1/2" 5 start lead screw and the 3/8" 5 start lead screws will it all work together

    If the turns per inch on a lead screw is different, then the nut on the lead screw will move at a different velocity.

    Additional Information:
    Let me explain in more detail.

    Let's say you have two lead screws:

    - 1/2" 5 starts at 10 TPI = 2 turns per inch. (5 starts / 10 TPI = 1/2 inches per turn or 10 TPI / 5 Starts = 2 turns per inch.)

    - 3/8" 2 starts at 10 TPI = 5 turns per inch. (2 starts / 10 TPI = 1/5 inches per turn or 10 TPI / 2 starts = 5 turns per inch.)


    So, if two stepper motors (one connected to the 1/2" lead screw and the other connected to the 3/8" lead screw) turned 10 revolutions in 2 seconds, the 1/2" lead nut would travel 5 inches and the 3/8" lead nut would travel 2 inches at the 2 second mark.

    Click the link to add information to this solution:
    If I buy the 1/2" 5 start lead screw and the 3/8" 5 start lead screws will it all work together

  • Can 3/8" lead screw be used instead of 1/2" on the 'BOOK' machine?

    Yes, you will only need to change the coupling that couples the motor to the 3/8" lead screw.

    Additional Information:
    Yes, you will only need to change the coupling that couples the motor to the 3/8" lead screw.

    Click the link to add information to this solution:
    Can 3/8" lead screw be used instead of 1/2" on the 'BOOK' machine?

  • WHAT IS SHIPPING DIMENSIONS AND WEIGHT FOR THE VERTICAL LASER.

    Shipping crate size 121" X 36" X 92"

    Weight 511 LBS

    Click the link to add information to this solution:
    WHAT IS SHIPPING DIMENSIONS AND WEIGHT FOR THE VERTICAL LASER.

  • WHAT IS THE SHIPPING WEIGHT AND DIMENSIONS FOR GREENLEAN?

    Shipping crate 121" X 36" X 92"

    Weight 511 LBS

    Additional Information:
    ship in india pls

    Additional Information:
    International shipping rates can be determined by:
    - adding products to the cart
    - go to the cart and enter shipped by address
    - and pressing the calculate shipping button

    Click the link to add information to this solution:
    WHAT IS THE SHIPPING WEIGHT AND DIMENSIONS FOR GREENLEAN?

  • If I order 19ft of the 1/2" lead screw will it come in three 6'5" lengths by default? This is what I need. Thanks

    No they will not come in that length as a default, we would contact the buyer to ask specific lengths due to the total length purchased.

    However if you order the 1/2" lead screw we can get them cut to the specific length you require, by contacting us here or call us at 281-815-7701.

    Click the link to add information to this solution:
    If I order 19ft of the 1/2" lead screw will it come in three 6'5" lengths by default? This is what I need. Thanks

  • What output pins on your BOB are used to control the SuperPID?

    Yes, you can use any two of the output terminals of the breakout board to control the SuperPID closed loop router controller (a diagram is not needed with these instructions).

    One output terminal will be used as an on/off (1/0 or 5v/gnd) that will be invoked with the M3/M4/M5 M-codes in your g-code instructions.

    The other terminal will be connected to either another 5v/gnd signal to control speed for 5000/20000 rpm or for PWM output (recommended) for proportional speed control.

    To setup this configuration in Mach3, go to your ports and pins dialog box (config menu -> ports and pins). Click on the spindle setup tab. In the Motor Control Section of the dialog, check the box for Use Spindle Motor Output and check the box for PWM control. Change the PWM Base Frequency to 50Hz.

    Click the link to add information to this solution:
    What output pins on your BOB are used to control the SuperPID?

  • WHAT TERMINALS ARE USED TO CONNECT THE INVERTER WALL OUTLET?

    Input to VFD:
    240V Active - R
    240V Neutral - S
    Ground - E

    Additional Information:

    Click the link to add information to this solution:
    WHAT TERMINALS ARE USED TO CONNECT THE INVERTER WALL OUTLET?

  • I just ordered a 1/2" lead screw and bearings, etc. But I don't see any 1/2" shim washers for those bearings. If you have any, please toss 8 of them in the shipment and I'll gladly reimburse you.

    We will provide shim washers as a part of machine assemblies, but when purchasing lead screw and bearings, the shim washers must be purchased as well. Please give us a call and we can send them out.

    Click the link to add information to this solution:
    I just ordered a 1/2" lead screw and bearings, etc. But I don't see any 1/2" shim washers for those bearings. If you have any, please toss 8 of them in the shipment and I'll gladly reimburse you.

  • WHAT CAUSES ONE OF MY TWO AXIS MOTORS TO STOP WHILE THE MACH3 PROGRAM IS STILL RUNNING

    If one of your stepper motors decides to stop moving and the others are moving during a CNC milling or laser cutting job, then there could be two things that could be causing this.

    - The motor found its limiting torque (usually comes with a not-so-pleasant sound). This is where the control software is trying to move the stepper motor too fast (velocity, or too fast too quickly, acceleration) and the load against the stepper motor (inertia of the machine, or the material against the end mill while milling). Recommended action is to lower the velocity and/or acceleration, and/or lower the feedrate when cutting.

    - There is a wiring issue with the wiring from the driver to the motor. This could be a loose wire, or a chafed wire (or two shorting together). It can also be a loose digital wire from the controller board to the driver. Sometimes wire ties can be the culprit. Recommended action would be to thoroughly inspect the wiring.

    It's probably not the limit switches since that would cause a stop to the entire motion of the cnc router or laser machine.

    Sometimes Mach3 will show a status when something goes wrong, but in cases where the motor is stopping due to its torque limit, then that would not be shown in the status. It's always good to check it anyway.

    Additional Information:
    I need to clarify my situation a little better after going to my shop and trying to run another program on Mach 3. About 15 minutes into the milling process all the motors (2-X axis, Y axis and Z axis)stop but the program continues to run. I stop the program and after a couple of minutes when I try to restart the program all the motors start working again. Then after another 15 minutes or so, all the motors stop again. I checked and rechecked my wiring. This has never happened to me before when running the same programs with the same setups and motor speeds. All of a sudden when I reloaded a program I successfully used before it does this. Do you have any recommendations?

    Additional Information:
    Yeah, it sounds like a more complex issue. Have you tried running in the air without using the spindle. This may be a power related issue.

    Additional Information:
    That's exactly what I did. I ran the program without the router motor on just to see if the motors would get through the whole program but they stopped working after about fifteen minutes and then I was able to start them again after about 3 or 4 minutes. I never had this problem before so you can imagine my frustration especially after ruining a couple of projects on expensive material.

    Additional Information:
    Sure. I can completely understand. Try this: disconnect all but one of the driver from power and digital connection and do the air run. Repeat this for each driver and note your findings. This will rule out the drivers causing a power failure.

    Also, is your stepper motors and drivers on a separate power circuit from the computer?

    Additional Information:
    I will try disconnecting each driver and digital connection, which will be a real pain because it will be hard to access.

    All the stepper motors, drivers and computer are plugged into the same power strip.

    Additional Information:
    Ok, so there is no power failure going on, but I believe it is necessary to test each stepper motor and driver pair individually. Hopefully that will lead to a conclusion.

    Additional Information:
    It will take a little time but I will do it and report back on my findings.

    Additional Information:
    Curious, what machine is exhibiting this problem?

    Additional Information:
    I purchased a BYCNC kit back in 2009 with an approximate cutting area of 2' X 4'. I later changed out the Z-Axis Motor and controller for a larger one and have two X-axis motors and controllers. In 2010 I rebuilt the machine out of birch plywood instead of the particle board that the kit supplied. I sent Patrick pictures to him. The machine never gave me a problem till now.

    Additional Information:
    Thanks for the update. This is Patrick by the way. I answer pretty much all of the Customer Service questions. That machine has given quite a good history.

    Additional Information:
    I love the machine and made a number of samples of my work for my e-commerce site, but I can't start selling product until I know this problem is solved because I will not be able to fulfill orders. I finally got all the electronics out of its enclosed protected area near the machine so that I test each controller as you recommended. I hope the problem can be rectified. Will let you know.

    Additional Information:
    Thanks.

    Additional Information:
    I tested each stepper motor and driver pair individually and they worked so what might be the next step?

    Additional Information:
    Did each stepper motor driver pair work for the full +15 minutes?

    Additional Information:
    Yes, I had them in operation for over 30 minutes.

    Additional Information:
    Ok, well it’s good that the motors and driver are ok. We are now down to the power supply and the breakout board as possible causes for the stop. I have a feeling it may be the power supply where with all three drivers drawing current and the power supply maybe getting too hot. Is the fan in the power supply working? You can also test to see if there is 36 volts on the power supply voltage output (V+ and V-).

    Regarding the breakout board, if you have an oscilloscope, you can test if the driver pulses are outputting, but I would consider this as a last resort after you determine if there is a problem with the power supply.

    Additional Information:
    I tested the power supply with a voltmeter and each output was registering 39-40 volts. I think the problem may be the g-code. I am using V-Carve pro to do design and output to Mach 3 Mill g-code. When I studied the g-code lines I noticed that further into the program the z-axis g-code stopped zeroing out to move to the next part of the carving. In other words both the x and y keep moving and the z just stopped working because there was g-code missing. I think something is missing when the design was converted to g-code. I noticed that when I ran a simpler project it worked without problems so I need to investigate this further.

    Additional Information:
    New Update, Its not the g-code. I started to run the long program and everything was working fine until about 45 minutes into it, all the motors stopped working (but the program was still running) and there was a high pitched hum. When I put my hands on the motors they were all trying to move but it seemed they were all stalled. I turned the power off, gave it a minute and when I turned it back on I was able to move the motors again. Could this be a power supply problem?

    Additional Information:
    It does sound more and more like a power supply problem. Did you test the power supply after the motors stopped?

    Additional Information:
    No, I did not. What should I be looking for.

    Additional Information:
    It’s good that you know the voltage during normal operation, so you have a base understood. If the power supply is the problem, the voltage will be reduced or non existent when measured after the problem.

    Additional Information:
    Also, check to see if the fan is running on the power supply when the motors stop. That may (not absolutely) be an indication.

    Additional Information:
    I'll run another test, check the voltage and fan when the problem occurs and let you know. Thanks for hanging in there with me as we try to resolve the problem.

    Additional Information:
    It’s my pleasure. This service is rarely used and is faster then email. Odd nobody uses it. Any recommendations you can give would be great. No problem using this FAQ to pose ideas as this resolution will be cleaned up later.

    Additional Information:
    It might be that people do not realize you can communicate through the sight like this because they are so used to e-mail and texting. You may want to explain this feature in the customer service section.

    I ran the program this morning and it did not take long before the motors stopped. While operating the voltages for all three motors was 46 volts, when the motors stalled (and again there was a high pitch hum) the voltage went up to 60 volts and the fan on the power supply was operating.

    Additional Information:
    So, the driver work individually, but not all together. There is a high pitch sound when the motors fail. You have noted 60 volts from the power supply and the supply fan remains on. This is a difficult issue to resolve, but it seems to me that your power supply may be bad. The 60v measurement tells me that the current dropped and ohms law tells us that is current drops, volts will rise if the resistance stays the same.

    Additional Information:
    As one last test I am going to test each driver again and let them go through the entire program because it seems that the failure can occur at the beginning or towards the end of the program. When I originally tested ach driver I let them run for about a half an hour and the program takes over an hour to run completely. I just want to make sure that it is not the drivers. I will report back when I finished but as you noted it may be the power supply but I want to make sure.

    Additional Information:
    That’s a great idea.

    Additional Information:
    I just ran the x-axis through the whole program and there was no problem especially since I have two NEMA 23 motors moving that axis. Before I check the Y and Z could having a NEMA 34 on the Z axis with appropriate controller be a problem. I used the larger motor on the z axis because the router I am using is a large 1 1/2 hp. I've run this program in the past with this set-up and have not had a problem.

    Additional Information:
    Having a, say 3.0 amp driver, driving a stepper motor that typically requires a 6 amp driver would not seem to be an issue since the driver is limiting the current draw, but the driver may not be able to handle larger coil and back EMF with the protection on the 3.0 amp driver. With that said, I don’t believe that is the issue in this case.

    Additional Information:
    I don't either because I was able to run this and other complicated programs with this set-up in the past. I will let you know on the y and z axis.

    Additional Information:
    Thanks

    Additional Information:
    I ran the Y axis and z axis separately through the entire program and there was no stopping or problem. I guess the culprit is the power supply and I'll order a new one and hope that resolves the problem.

    Additional Information:
    Yes, that is the most probable cause. Please keep me informed. Thanks!

    Additional Information:
    Received and installed the new power supply. I ran the program with the router on and it worked flawlessly. The program runs for an hour and a half and I did not have a single problem. I guess it was the power supply but I was glad to go through all the diagnostics we discussed before replacing it. I hope this power supply lasts a lot longer than the last one. Thanks much for hanging in there with me and coming up with the solution.

    Additional Information:
    It’s my absolute pleasure and I am so happy to hear that the power supply replacement solved the problem.

    Additional Information:


    Additional Information:
    Y axis stop working X & Z work fine Y axis has two motors have check wiring & connections new breakout board still the same port & Pin set OK dont no were to go next David

    Additional Information:


    Additional Information:
    my cnc plasma cutter will run out the program when cutting. what is the cause?

    Additional Information:
    The cnc plasma question shod be a separate question. Can you pise that question by clicking the customer service live menu button at the top? Thanks.

    Click the link to add information to this solution:
    WHAT CAUSES ONE OF MY TWO AXIS MOTORS TO STOP WHILE THE MACH3 PROGRAM IS STILL RUNNING

  • What is the inner depth of the 1/2" to 1/2" rigid coupling?

    The inner depth of the 1/2" to 1/2" rigid coupling, would be 1.4205in or 36.08mm.

    Click the link to add information to this solution:
    What is the inner depth of the 1/2" to 1/2" rigid coupling?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.