PC with parallel port and USB port
20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
18awg stranded wires for power supply to drivers
24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
- If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

Additional Information:

Click the link to add information to this solution:
can you please clarify exactly what I receive w/ 5' x 10' CNC machine kit and what additional items I would need to have a fully operational machine?

Hi, you can call me at the 281-815-7701 number. Please leave a message when you call as most of the calls are screened to avoid scam calls. You can also email me at customerservice@buildyourcnc.com or phooddaniel@berkeley.edu.

The newer kits that are featured on the home page include everything you need except a computer and software. The legacy CNC routers that are located in the CNC machines menu selection include all of the parts for the gantry, but you will need to build the table yourself. All of the information on the measurements to be followed for the table construction are on the machine pages.

Click the link to add information to this solution:
I am looking at getting a 4x8 cnc router kit. I am having a hard time figuring out what is included in the kit and what else i will need to buy with it to get off the ground and running. Is there someone i could talk to to walk me through it? If not, can you break down what all I need to go from scratch to a running set up? thanks

We carry several sizes of lead screw and stepper motors on our website, for example here https://buildyourcnc.com/Item/mechanical-leadscrews-lead-screw-!5-5-starts-10-tpi and here https://buildyourcnc.com/ProductSearchResults.aspx. Please call us at 281-815-7701 to discuss the particular lengths you would need and shipping options.

Additional Information:
https://buildyourcnc.com/ProductSearchResults.aspx is not working

Additional Information:



Additional Information:

Click the link to add information to this solution:
I have a project very similar to cnc machine. I need 3 lead screws of 1.8 m with all set (supports, bearings...etc). and 3 NEMA 42 motors that I can connect with. if those are available, I need the information about shipping to Oman or UAE.

The RNRMotion driver will not conflict with the mach3 license. Make sure you have the RNRmotion driver in the plugins folder and the provided xml in the main mach3 folder. Also, make sure to have the mach3 license file in the mach3 folder. If you still experience problems, please give us a call.

Click the link to add information to this solution:
i purchased a breakout board from you guy and the rnr motion control is messing with my license in mach 3 tech support at mach said it is the rnr software i need help to contact them and let them see what they can do to help

We currently cannot release or sell any plans at this current moment! We apologize for this inconvenience, however if you email us at customerservice@buildyourcnc.com. We can help you get the current parts you will need, for a fully functional 2.2kW z-axis assembly.

Click the link to add information to this solution:
I purachased a bluechick from you in 2011. I am upgrading from a Porter-cable router to a 2.2kw spindle. Can you supply me with drawings for the spindle mount so that I can cut the parts?

Yes, if you need a replacement part on your machine please call us at 281-815-7701.

Click the link to add information to this solution:
I have a blacktooth laser engraver. The Y Axis stepper motor needs to be replaced. Can you please provide me with the information I would need to replace this motor.

Hola puedo venderte una maquina nueva completa chocofrutfc@yahoo.es

Click the link to add information to this solution:
Hi, I’m purchasing an ox build workbee cnc router from China but I need to purchase the spindle mount, router and all cables/wires. Please can you give a list and quote of what I will need? I am purchasing the electrical pack with it but it doesn’t come with the cables and all other bits I need. Thank tou

PC with parallel port and USB port
20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
18awg stranded wires for power supply to drivers
24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
- If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

Additional Information:

Click the link to add information to this solution:
what I receive w/ 5' x 10' CNC machine kit and what additional items I would need to have a fully operational machine?

The connections between the driver and the breakout board(USB/Parallel)22-24 AWG wire is preference also going from the potentiometer going to LSPS(laser power supply) , now going from the power supply to the drivers/laser power supply 16-18 AWG wire is our preference.

Click the link to add information to this solution:
I'm about to order your laser cutter , item 279 and a little confused.. in your faq it states you need wire and connectors for assembly, can you be specific on amount and guage of wire or tell me where to find that information?

There are two things to consider when using two stepping motors on a single axis. Since you want both motors to spin at the same rate and possibly in the same direction, you need to connect both motor drivers to the same breakout board pins. For example, if you want two motors on the x-axis and the x-axis pins on the breakout board are #2 for step and #3 for direction, the #2 will connect to the step (cp) terminal on each driver and the #3 will connect to the dir (cw) terminal on each driver.

However, if the motors will be opposing (one motor will need to spin in the other direction), you will need to consider either flipping the rack on one side, or adding a circuit to invert the direction (#3) signal going to that driver.

Click the link to add information to this solution:
I'm planning a rack and pinion style gantry, and need clarification on how to slave a second stepper to the Y (or X). Can you direct me to that information for your products?

For the 2.2kW Spindle you would need the ER20 1/2" Collet.

Click the link to add information to this solution:
What 1/2" collet and nut do I use for the Greenbull with the 2KW spindle? I want to order the Onsrud Spoilboard surfacing cutter.

Here is how to connect your router to the parallel breakout board through the on-board relay. You will need a spare extension cord. You will need to remove a portion of the outer jacket of the extension cord to expose the white, black and green wires (white = neutral, black = live and green = ground), understanding that the neutral and live create the completed circuit.

See this image of a similar connection. The terminal has the same connections.
https://www.buildyourcnc.com/images/vacuum-pressure-controller-relay-terminals-700.JPG

Image of the relay terminal:
https://www.buildyourcnc.com/images/breakoutboardrelayNONC.PNG

The live/black wire would be cut and one end of the cut would be secured into the P terminal and the other cut end would be secured into the S terminal. The live and ground wire would be uncut and travel from the plug to the router.


Additional Information:
You can also connect other high powered devices to the breakout board using any of the output terminals. You will need to supply extra relays like the one shown here:
https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Or you can find SSRs (Solid State Relays) that will accept 5v to drive the relay coil. Make sure the SSR will protect the 5V line from Back EMF as there is a coil in the relay. The one we sell contains a fly-back diode to protect the 5v terminal.

Click the link to add information to this solution:
I have your breakout board with relay parallel port , I have a vacuum, light on router and air pump I want to also hook up to board, can I hook those up to board and also could I had reylays to each one, what is the best way to figure this out any information would be great. Thanks

Other items you will need if you are purchasing the electronic combo (motors, drivers, power supply and computer interface) and the hardware and plans kit:

You will need the wood to create the structure of the machine. You will need a router to serve as the cutting instrument. You will need a computer to control the machine and the software that will serve as the control program. You will also need lead screws and rails (aluminum angles). If you intend to have faster travel than 20 ipm, we recommend purchasing the 5 start lead screws so you can achieve up to 300 ipm. https://www.buildyourcnc.com/item/mechanical-leadscrews-leadnuts-!5-5-starts-10-tpi

Click the link to add information to this solution:
if i purchase the 4 Axis Electronic Combos and the Combo #1 with hardware, plans and DVD what else do i need to have a complete cnc machine

The bluchick CNC router is a perfect small format CNC that can handle most jobs. Please check here to see the latest information on this CNC router. blueChick CNC Machine. The machine can be purchased assembled. Al you will need is a computer and spindle.

Click the link to add information to this solution:
I'm looking for a complete CNC router, out the box ready to use system. Computer and software. What do you suggest? I need a working area of 12"x24"

The size of the stepper motor is measured in holding torque, generally oz/in. You will determine the torque loads of your axes when selecting steppers. Once you know which stepper you need, the drivers and controller board are simple to pair with them.

Click the link to add information to this solution:
I'm trying to build my CNC router 3m*1.3m, but i'm not sure what is the type of stepper motor i should pay, all my CNC body is Al. I need to bay 4 Stepper motors, 4 drivers, spindle, inverter, and i don't know what is the type of controller ?

To determine the status of your order, simply log in and click on the "[My Account]" link at the top of the page. If you purchased as a guest, you will need to call the office to determine the status and get the tracking number for your order.

The office phone number can be found by clicking "Need Help?" is located at the top right of all buildyourcnc.com web pages.

Click the link to add information to this solution:
I placed an order for a 4th axis with tailstock on Wednesday and was just wanting to check on the shipment status. I'm needing the item early next week and need to confirm that it will arrive in time. Thank you.

We currently do not sell any plan's for any of our machines, only for our scratch and build kit.

Click the link to add information to this solution:
Would you sell a kit that has all of the hardware and electronics with CNC plans for the table and gantry? Some of have access to a CNC temporarily (TechShop) but want one of our own.

That will depend on the controller that was installed in the redFly. If the controller is a pokeys57CNC controller, you can use Mach 4 with that system.

You can add a 4th axis and an ATC (Automatic Tool Changer) with the redFly system.

Click the link to add information to this solution:
Does the Redfly that I bought with the GreenBull in 2016 work with Mach4? Also I want to add a 4th axis and a spindle with automatic tool changer. Will this work too or do I need a new control board? I bought my CNC with a longer Z travel, so I have plenty of room for these. Thanks!

Mach3 and Mach4 typically use specific controller cards that are compatible with the software. If your controller connects to your computer using either a USB or Ethernet connection, then you will probably need to change the controller card as well, unless your controller card contains a plug-in that works with the Mach3 or Mach4 software.

Click the link to add information to this solution:
I have cnc fiber laser cutting machines it has operating software cypcut and I need to change it to Mech 3 or 4 do I have to buy the driver card with the software or only the software?