[ Log In ]
[ Register ]

Question #: 541

Question: THE CNC MACHINE IS UNSAFE WITH EXPOSED SPROCKETS THAT CAN DAMAGE FINGERS AND HAVE CLOTHING CAUGHT IN IT.

Current Solution

These machines are inherently dangerous. Before the machine moves, the machine should be clear of any person by a dimension of at the distance of a persons reach plus a few more feet. This is the policies we institute in our shop and what is recommend to all of our customers. Treat these machines as you would treat any major power tool in the shop.

With that said, you can certainly add some protective parts, but still keep folks away even with those installed. I would use the gantry side to do all of the mounting of the protective parts. Consider using sheet metal that you can bend and make a simple installation right on the gantry side.

Additional Information:

Respond:

Other Possible Solutions to this Question

  • Can I purchase a computer off Amazon (I have a machine I want to use) and still use the USB interface to drive it with LinuxCNC?

    You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
    There is no estimate on how much this will cost though, since there are too many variables involved to do this.

    - PC with parallel port and USB port
    - 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
    - 18awg stranded wires for power supply to drivers
    - 24awg stranded wires for breakout board to drivers
    (location and spacing of components varies from one person to another, so we do not provide cables/wires)
    - General purpose extension cord (cut the female end off) to provide power to power supply
    - USB cable to power breakout board
    - Parallel cable to communicate to breakout board
    - Router
    - (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
    - (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
    - End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
    - CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
    - CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

    This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

    Click the link to add information to this solution:
    Can I purchase a computer off Amazon (I have a machine I want to use) and still use the USB interface to drive it with LinuxCNC?

  • On the blackFoot 4'x8' CNC machine do you have the instructions under one file that I can download, I want to print them out and make notes as I am building the machine.

    WE don't have an actual file that contains the instructions for the machines as they are a part of a larger database file that is queried during the product page's rendering in the browser. The best option would be to print the webpage on a printer and use that as notes.

    I know this will not provide larger images, but you could use the paper version to write your notes while assembling the machine using the larger images on the website.

    Click the link to add information to this solution:
    On the blackFoot 4'x8' CNC machine do you have the instructions under one file that I can download, I want to print them out and make notes as I am building the machine.

  • I am having trouble connecting the cambam program with my Mach3 to my 4X8 Blackfoot CNC machine. Where can I get help on this issue. Have had my machine since 2015 and have not been able to use it. Thank you

    CamBam specifically creates the g-code (machining operations) instructions to be loaded into Mach3. Make sure in your CamBam g-code file parameters, you are using the Mach3 post processor. If you have already done this, let me know. If you are not sure how to do this, let me know.

    Click the link to add information to this solution:
    I am having trouble connecting the cambam program with my Mach3 to my 4X8 Blackfoot CNC machine. Where can I get help on this issue. Have had my machine since 2015 and have not been able to use it. Thank you

  • I have a blueChick version 4.2 CNC Machine with no schematics for it is there anyway possibly i can get them so i can finish putting my cnc together

    To assemble the blueChick v4.2, you will need two sets of instructions, the assembly instructions for the main body and mechanicals of the CNC machine, and the instructions to connect and test all of the electronics.

    The assembly instructions are located at this URL towards the bottom of the page (click on each picture to get a larger view):

    https://www.buildyourcnc.com/blueChickVersion42CNCMachineKit.aspx

    The instructions to connect and test the electronics can be found at this URL:

    https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

    Click the link to add information to this solution:
    I have a blueChick version 4.2 CNC Machine with no schematics for it is there anyway possibly i can get them so i can finish putting my cnc together

  • I purchased a 4ft X 8ft Blackfoot CNC machine in 2015 and to this date have not been able to use it. How can I get some help. Thank u
  • I am building the CNC in your book - Build you own CNC Machine. One of the bearing thicknesses is 1/4" I can't find that bearing online. I can find 9/32, will that be a problem. Do you have a source? Thx

    As long as the bearing has a minimum thickness of 1/4" and 9/32" is a bit thicker, there will be no problem with the book build using the bearing that is 1/32" thicker. There is actually more surface area which is better.

    Click the link to add information to this solution:
    I am building the CNC in your book - Build you own CNC Machine. One of the bearing thicknesses is 1/4" I can't find that bearing online. I can find 9/32, will that be a problem. Do you have a source? Thx

  • Hello. I am interested in the green bull 6X long z CNC machine with electronics. I live in NZ, where the voltage is 230 V and 50 Hz. is it going to be possible to get the inverter to run here? Thanks!

    Dealing with our inverters, they are built with a bit of margin on the input power. For our 220V VFD the margin is from 170-250V 50/60Hz, so running our VFD in your location will not be an issue! Our electronics will not have a issue running at 230V as well.

    Click the link to add information to this solution:
    Hello. I am interested in the green bull 6X long z CNC machine with electronics. I live in NZ, where the voltage is 230 V and 50 Hz. is it going to be possible to get the inverter to run here? Thanks!

  • Just bought Build Your own CNC Machine book. It is missing the chapter on lead screws that is described on page 181 at the end of Chaprer 16. Where can I get this info?

    It sounds like you got a misprinted book. If you purchased it from us, please contact us directly for a replacement. If you bought it from Amazon or a third party, you'll need to contact them. General information about lead screws is available on this website and at buildyourtools.com.

    Click the link to add information to this solution:
    Just bought Build Your own CNC Machine book. It is missing the chapter on lead screws that is described on page 181 at the end of Chaprer 16. Where can I get this info?

  • I have the build your own CNC kit 3 Axis CNC Machine 2008, were can I get the Gcode or vector files for it ? I wanted to have it laser cut

    Gcode or digital files are not available for our machines.

    Additional Information:

    Click the link to add information to this solution:
    I have the build your own CNC kit 3 Axis CNC Machine 2008, were can I get the Gcode or vector files for it ? I wanted to have it laser cut

  • I have nearly completed the CNC machine from the book, but I am using it with a USB breakout board, and have no idea how to wire the 6 limit switches to the board. I'm having difficulty following the diagram on the USB breakout board screen. Can someone please help me?

    Sure, the USB interface has a place for 4 axes of limit switches.

    Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

    A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

    Let me know if this information was helpful (or not) by adding information to this question. Thanks.

    User response:
    Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
    Thank you.

    buildyourcnc response:
    On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

    Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

    In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

    There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

    Click the link to add information to this solution:
    I have nearly completed the CNC machine from the book, but I am using it with a USB breakout board, and have no idea how to wire the 6 limit switches to the board. I'm having difficulty following the diagram on the USB breakout board screen. Can someone please help me?

  • I have a CNC Machine from China, and the Breakout Board is not Labeled. Is there any way to test the board using Mach3 to find out the pin designations? db25 bob

    (These steps are to be taken with precaution, due to the fact that we do not know the model or manufacturers specifications for your BoB)

    Here is a link to our CNC electronic videos(

    &list=PL122021172205E9AA&index=1).
    Try using this to compare the one you have to our older model version BoB, try setting up your X-axis to work wiring it to your driver and motor, and power supply.
    For further assistance email: customerservice@buildyourcnc.com

    I would recommend trying to contact them if possible to avoid any serious damages to your product.

    Click the link to add information to this solution:
    I have a CNC Machine from China, and the Breakout Board is not Labeled. Is there any way to test the board using Mach3 to find out the pin designations? db25 bob

  • Hello  We would like to buy a greenLean Vertically Oriented CNC Machine we start from scratch and want to make sure that we get all the pieces, we need  hardware and software we have a PC and a Mac

    If you purchase the greenLean, you will get everything you need except a router, computer to operate the machine, and software to control the machine. You state that you have a computer. You can use this computer, but you will need to determine if it has a parallel port, or if you are going to need the USB controller option. As for the software, there are too many different options for you to choose from. We would not be able to tell you which to get, and how much it will cost you. This is a matter of preference. I can tell you, however, that you will need 3 types of software to complete a CNC project. You will need CAD software to design your design, CAM software to add tool paths and convert the design to g-code, and then control software to take the g-code and operate the machine.

    Additional Information:
    20

    Click the link to add information to this solution:
    Hello  We would like to buy a greenLean Vertically Oriented CNC Machine we start from scratch and want to make sure that we get all the pieces, we need  hardware and software we have a PC and a Mac

  • Hello  We would like to buy a greenLean Vertically Oriented CNC Machine we start from scratch and want to make sure that we get all the pieces, we need  hardware and software we have a PC and a Mac

    If you purchase the greenLean, you will get everything you need except a router, computer to operate the machine, and software to control the machine. You state that you have a computer. You can use this computer, but you will need to determine if it has a parallel port, or if you are going to need the USB controller option. As for the software, there are too many different options for you to choose from. We would not be able to tell you which to get, and how much it will cost you. This is a matter of preference. I can tell you, however, that you will need 3 types of software to complete a CNC project. You will need CAD software to design your design, CAM software to add tool paths and convert the design to g-code, and then control software to take the g-code and operate the machine.

    Additional Information:
    20

    Click the link to add information to this solution:
    Hello  We would like to buy a greenLean Vertically Oriented CNC Machine we start from scratch and want to make sure that we get all the pieces, we need  hardware and software we have a PC and a Mac

  • IF I PURCHASE A GREENBULL 6X LONG Z CNC MACHINE KIT AND MACH3, WHAT ELSE WOULD BE REQUIRED TO ASSEMBLE THE WORKING MACHINE? HAVE CAD SOFTWARE.

    You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
    There is no estimate on how much this will cost though, since there are too many variables involved to do this.

    - PC with parallel port and USB port
    - 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
    - 18awg stranded wires for power supply to drivers
    - 24awg stranded wires for breakout board to drivers
    (location and spacing of components varies from one person to another, so we do not provide cables/wires)
    - General purpose extension cord (cut the female end off) to provide power to power supply
    - USB cable to power breakout board
    - Parallel cable to communicate to breakout board
    - Router
    - (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
    - (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
    - End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
    - CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
    - CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

    This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

    Click the link to add information to this solution:
    IF I PURCHASE A GREENBULL 6X LONG Z CNC MACHINE KIT AND MACH3, WHAT ELSE WOULD BE REQUIRED TO ASSEMBLE THE WORKING MACHINE? HAVE CAD SOFTWARE.

  • If I purchase a greenBull 6X Long Z CNC Machine Kit and Mach3, what else would be required to assemble the working machine? I have CAD software.

    You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
    There is no estimate on how much this will cost though, since there are too many variables involved to do this.

    - PC with parallel port and USB port
    - 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
    - 18awg stranded wires for power supply to drivers
    - 24awg stranded wires for breakout board to drivers
    (location and spacing of components varies from one person to another, so we do not provide cables/wires)
    - General purpose extension cord (cut the female end off) to provide power to power supply
    - USB cable to power breakout board
    - Parallel cable to communicate to breakout board
    - Router
    - (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
    - (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
    - End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
    - CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
    - CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

    This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

    Click the link to add information to this solution:
    If I purchase a greenBull 6X Long Z CNC Machine Kit and Mach3, what else would be required to assemble the working machine? I have CAD software.

  • I have the older discontinued USB breakout board. The y-axis no longer works and have traced it to the breakout board. Is there a replacement board that can use the same Planet CNC software running on Windows 10?

    No, we have gotten away from the planet-cnc boards as they have decided to not support our board with their software. You can use the Mach3 USB board as an alternative. You will be better off with Mach3 as a control software as this is widely used and supported.

    Mach3 USB board:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Click the link to add information to this solution:
    I have the older discontinued USB breakout board. The y-axis no longer works and have traced it to the breakout board. Is there a replacement board that can use the same Planet CNC software running on Windows 10?

  • can you please clarify exactly what I receive w/ 5' x 10' CNC machine kit and what additional items I would need to have a fully operational machine?

    PC with parallel port and USB port
    20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
    18awg stranded wires for power supply to drivers
    24awg stranded wires for breakout board to drivers
    (location and spacing of components varies from one person to another, so we do not provide cables/wires)
    - General purpose extension cord (cut the female end off) to provide power to power supply
    - USB cable to power breakout board
    - Parallel cable to communicate to breakout board
    - Router
    - (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
    - (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
    - End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
    - CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
    - CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
    - If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

    Additional Information:

    Click the link to add information to this solution:
    can you please clarify exactly what I receive w/ 5' x 10' CNC machine kit and what additional items I would need to have a fully operational machine?

  • I have a blueChick 13"x24" or 13"x36" Desktop CNC Router Kit v3.0 (Timing Belt) that I've assembled but never was able to get it running. Can BuildYourCNC assist me in selling this machine? Do you have used machine offerings on your site?

    We would highly recommend using our forums to sell you machine buildyourtools.com.
    We currently do not have a page or option to allow our customers to sell our machines, you can also contact us at customerservice@buildyourcnc.com, for further assistance dealing with the machine and in regards to selling it.

    Click the link to add information to this solution:
    I have a blueChick 13"x24" or 13"x36" Desktop CNC Router Kit v3.0 (Timing Belt) that I've assembled but never was able to get it running. Can BuildYourCNC assist me in selling this machine? Do you have used machine offerings on your site?

  • USING MACH3, MY MACHINE STOPS IN THE MIDDLE OF A PROJECT. HOW CAN IT BE STARTED AGAIN FROM POINT STOPPED?

    Dealing with a mid-stop cut via Mach3, you will have to be careful if it is intentionally or unintentional. If you desire to stop your machine while in the middle of a cut be sure to stop it when the machine is moving in an upward motion on the z-axis and the X/Y-axis are stationary. Then you can choose the point (G-code) where the machine was left off and click on the Run from here button on the Program Run screen (left hand side) right above the Reset button.
    (Make sure spindle/router is running before hand!)

    Now if the machine stops unintentionally, and was moving in either the X/Y-axis, then it will be difficult to run the machine from the original point dealing with the coordinates might have been lost due the the machine continuing motion but via Mach3 the machine has stopped.

    If this occurs to fight this issue before hand, is marking your home with the spindle/router to make a hole were your home is. Although moving it manually back to home the machine can be off by the smallest amount and could cause an inconsistent cut. If accuracy is something that can not be risked, then you can home the machine about a 1/4" or 1/2" down from the original home to start your cut on the same material but loosing that small piece.

    Additional Information:


    Additional Information:
    My typical go to solution is:

    - Note the current g-code line where the machine stopped.
    - If Mach3 errored and you cannot control the machine, Exit Mach3 - you may find that reset, stop does nothing to stop the spindle. When you exit mach3, the spindle will stop automatically.
    - Restart Mach3. The DRO (Digital Readout) should show the correct coordinates where the machine position was before exiting Mach3.
    - Scroll to the g-code line where the machine stopped. You may need to go a few lines prior to make sure you are not skipping any machining operations (which is why it is a good idea to learn the basics of g-code - don't worry, it's easy)
    - Click on the "Run from Here" button.
    - Mach3 will present you with a "Preparation Move" dialog box with the location that it will move to. If the coordinates shows a position that is into the material, make sure to specify a rapid height (clearance height) so the machine will move up first and then move to the location before moving down into the material. If the spindle is automatically controlled by Mach3, make sure to check the turn spindle on checkbox. If not, make sure the router or spindle is on before clicking OK.

    Additional Information:
    My cnc router stops at gcode line 50,000 and cannot finish program. They are about 150k of lines total. I have Mach3 and have bought the additional line capability. Is 50,000 (or around that) the limit? Is Mach 4 hobby license better and in what ways? Thanks! Mike Huber

    Additional Information:
    If you have a license for Mach3, then you should be able to run g-code indefinitely. I think there is something else going on.

    Additional Information:
    Additional Information:
    If you have a license for Mach3, then you should be able to run g-code indefinitely. I think there is something else going on.
    What else could be going on?

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:
    41PBGevE

    Additional Information:
    -1 OR 2+358-358-1=0+0+0+1 --

    Additional Information:
    -1 OR 2+69-69-1=0+0+0+1

    Additional Information:
    -1 OR 2+69-69-1=0+0+0+1

    Additional Information:
    -1' OR 2+902-902-1=0+0+0+1 --

    Additional Information:
    -1' OR 2+902-902-1=0+0+0+1 --

    Additional Information:
    -1' OR 2+730-730-1=0+0+0+1 or 'Qb1SuH5C'='

    Additional Information:
    -1" OR 2+161-161-1=0+0+0+1 --

    Additional Information:
    -1 OR 2+69-69-1=0+0+0+1

    Additional Information:
    if(now()=sysdate(),sleep(15),0)

    Additional Information:
    0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

    Additional Information:
    0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

    Additional Information:
    (select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

    Additional Information:
    (select(0)from(select(sleep(9)))v)/*'+(select(0)from(select(sleep(9)))v)+'"+(select(0)from(select(sleep(9)))v)+"*/

    Additional Information:
    (select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

    Additional Information:
    -1; waitfor delay '0:0:15' --

    Additional Information:
    -1; waitfor delay '0:0:19' --

    Additional Information:
    -1); waitfor delay '0:0:15' --

    Additional Information:
    -1)); waitfor delay '0:0:15' --

    Additional Information:
    1 waitfor delay '0:0:15' --

    Additional Information:
    O6enxjIS'; waitfor delay '0:0:15' --

    Additional Information:
    0MgObbnm'); waitfor delay '0:0:15' --

    Additional Information:
    8dan23Sv')); waitfor delay '0:0:15' --

    Additional Information:
    -5 OR 898=(SELECT 898 FROM PG_SLEEP(15))--

    Additional Information:
    -5 OR 353=(SELECT 353 FROM PG_SLEEP(19))--

    Additional Information:
    -5) OR 539=(SELECT 539 FROM PG_SLEEP(15))--

    Additional Information:
    -1)) OR 919=(SELECT 919 FROM PG_SLEEP(15))--

    Additional Information:
    xjpbAodW' OR 81=(SELECT 81 FROM PG_SLEEP(15))--

    Additional Information:
    r6v9pPjr') OR 551=(SELECT 551 FROM PG_SLEEP(15))--

    Additional Information:
    RDopsUKk')) OR 996=(SELECT 996 FROM PG_SLEEP(15))--

    Additional Information:

    *DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

    Additional Information:

    '||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

    Additional Information:
    1'"

    Additional Information:
    1����%2527%2522

    Additional Information:
    @@HCYaP

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    USING MACH3, MY MACHINE STOPS IN THE MIDDLE OF A PROJECT. HOW CAN IT BE STARTED AGAIN FROM POINT STOPPED?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.