I just posted the "enhanced" Blacktooth wiring diagram I developed. Check it out here.

http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

Click the link to add information to this solution:
Where do I wire the ground of my "th" and "power 0v - 5v" command on the power supply ? Is it possible to have a detailed blueprint of the electrical wiring (not for the blacktooth but in general) ? Many thanks :)

This would totally work for that application. This cable carrier is used for any object that needs to move and carries some electrical or tubing within it. This cable carrier is great for cable management where you want to make sure the wires and tubes are in a position that you set, not where the wires and tubing want to go.

Click the link to add information to this solution:
[311] I am looking to use this type of thing with a pipe for theater. Where the pipe can be lowered and it would have electrical and signal cable inside. Is this good for that or should I look at something else?

If you were logged in when you made the purchase, you can click the "My Account" link at the top of any page on this website and see all of your orders, order line items (with direct links to these items), and shipment information.

Here is a link to the "My Account" page for your convenience:
https://www.buildyourcnc.com/CustomerInfo.aspx

I did not see your username on your internal customer record, so I added this username and you should be able to see the information in the "My Account" page.

Additional Information:
I just tested your accounts page and the cable carrier links are in there. Thanks and please let me know if you need further assistance.

Click the link to add information to this solution:
I have purchased cable carrier chain and would like to know if you could send me a copy of that order as I need to purchase extra lengths of the links I bought. Thanks

The blackFoot uses the same electronics and motors as the blackToe (2'x4') machine. The only parts that change are the gantry horizontal structural parts which may be relatively easy for you to change. We can send you those parts if you are interested in a smaller unit.

Click the link to add information to this solution:
I have a Blackfoot that was purchased in 2017, after the purchase we moved and I haven’t been able to find room for it... would you be interested in buying it back or trading for something smaller. The Blackfoot and computer have never run but I did purchase it assembled. Thanks in advance, scott

There is a multitude of methods to create the table and frame for the greenBull long-z CNC machine, as some of the illustrations are shown on our gB webpage.

The image with the hollow mid section, is a custom table that will take advantage of the entire long-z axis assembly. So the frame can be built in that manner, however the CNC table should have its 3/4" table top. So you can cut standard sheets of wood, aluminum, plastics, etc.

So that specific illustration is not needed, however if you plan on cutting at that depth then it will defiantly benefit you to have that frame as shown in the illustration!

Click the link to add information to this solution:
Can you please clarify what a long Z axis table should look like? I've built a frame that matches the dimensions on the GreenBull page but under long Z it says a custom frame is required made out of steel, which I did. But do I need to have the frame open like shown in the picture or is that just showing what the table looks like under the 3/4 material?

When did you purchased the VFD and spindle? We only started this after the date of the instagram post that offered this added service.

Additional Information:
I purchased it July 16, 2020 however due to all the 2020 issues, I'm just now completing my CNC and hooking up the VFD and Spindle.

Additional Information:
The service started on Sept 23, 2020. Your order was prior to that.

The soldering is straightforward. If you wish to have me provide this extra service, feel free to send the unit back with the cable and I will solder the cable and do the parameter check and test the VFD and spindle.

Additional Information:
When I purchased my VFD and Spindle, I forgot to purchase the wire for the spindle. I had an electrician run a 220 line and hook up the VFD. But I don't have the wire for the spindle. I'd like to get the one you recommend and just pay you for another connector and the soldering.

Additional Information:
Can I purchase the one you spindle wire you recommend and just pay you for another connector and the soldering.

Click the link to add information to this solution:
You state "If you purchase cabling, we will solder the cable to the spindle and connect the cable to the VFD." I didn't see that when I purchased my spindle and vfd. If I place an order for the wire and another female adapter, will you please solder the connector to the wire?

That will depend on the controller that was installed in the redFly. If the controller is a pokeys57CNC controller, you can use Mach 4 with that system.

You can add a 4th axis and an ATC (Automatic Tool Changer) with the redFly system.

Click the link to add information to this solution:
Does the Redfly that I bought with the GreenBull in 2016 work with Mach4? Also I want to add a 4th axis and a spindle with automatic tool changer. Will this work too or do I need a new control board? I bought my CNC with a longer Z travel, so I have plenty of room for these. Thanks!

That is a very loaded question that could be replied in so many ways. I will need a more specific question to help you. For instance, I have my machine moving in different directions, but I don't know how to make the machine move according to g-code instructions. Another question could be, I connected all of my electronics and the motors are not moving and I did all of the steps on the electronics video to troubleshoot the problem.

Click the link to add information to this solution:
I have a cnc router that was built from the book "Build your own cnc machine" by james kelley and patrick hood daniel.all the parts were purchased from your company.I have no clue how to work the machine and I need to purchase a spindle (or router) bits , softwear ect , I did mention I don't know how to use the machine !!! Thanks for your help Richard

Stepper motors are known to make noises while function, however this does not affect accuracy or job function. However we recommend to check your wiring for solid connections, and for good connectivity!



On a personal note, here is one cool video dealing with making songs with stepper motors!

Click the link to add information to this solution:
I bought and built the Blacktooth laser cutter. It works, but one of the stepper motors makes a loud static hiss a second after the CNC power supply is turned on or off, and makes loud tweets and twirps when running. It seems to operate fine otherwise. I was wondering if it was "going bad" or if that is normal?

Is the cable between the mach3 USB and the YL260 shielded. If that does not solve the problem, add an induction coil to the cable to reduce any current fluctuations.

Click the link to add information to this solution:
Hello. I have bought an RnR Motion Controller and a YL260-A and I have it set up to the AVI from RnR to the VI1 of YL620-A but I'm getting that the RPM varies not like interference but like a drop from max value to min value. What could be happening?

There is some variation in the outward appearance of laser power supplies due to sourcing through different vendors. However, the basic wiring requirements are the same in each case. For the unit with integrated laser controller, follow the diagram found here: https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/0/. The terminals on the signal side will have a 6 connection terminal block -- these are the ones labeled 5V, IN, G, P (or WP), L (or TTL-L), and H (or TTL-H). The High Power side will have 3 inputs for AC power, one high voltage lead, and one return line. Connect these as shown in the diagram as well: the return line goes on the "front" (beam exit end) terminal of the laser tube, the high voltage lead goes to the "back" terminal of the tube, the FG terminal (or G) receives the earth ground wire of the AC power cable, and the two AC terminals receive the line and neutral wires of the AC power cable (it doesn't matter in this case which wire goes to which terminal).

Click the link to add information to this solution:
I purchased the blackTooth Laser Engraver with integrated Laser Control Unit and have been following your instructions. I noticed that the laser tube power supply is different that what is shown in your instructions. Do you have any better wiring guides that I can follow for the version that I received?

I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

The 2.5 amp driver can only accept a power supply between 12 volts and 24 volts. If a 36 volt power supply is used for this driver, the main driver chip will exceed its maximum voltage rating and cause failure.

If you need to spin your motor faster, you can either use a more appropriate driver (i.e. 3.0 amp driver) or you can change the mechanical parts so the axis has faster travel.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Can I connect a 36V power supply to 2.5 AMP Stepper Motor Driver. On the actual driver it shows 12V - 24V, but in the description and data sheet it indicates that it can accept 8V - 45V. Will I benefit from more powerful power supply. Thanks

The E.oA.A is an error that the VFD specifies as an overcurrent during ramp up (or acceleration). In other words, the spindle is trying to accelerate to quickly. The spindle cannot handle the inertia during ramp up and it is trying to draw too much current during this process. The best solution that I have researched is to increase the ramp up (acceleration) time, or slow the acceleration. You will need to check which programming setting you need to change, but there will be setting called acceleration time (or ramp up time). Increase this number in small increments until the error goes away. Then, increase it more so there is a safety factor.

Click the link to add information to this solution:
I have the 1.5kW spindle using the 110V vfd which I bought new and has never run correctly for me. The spindle will not accelerate to any reasonable speed before stopping. When it stops, the vfd display reads "E.oA.A". It does not appear to be wiring or settings, I have checked those many times. What else should I look at to troubleshoot this? Is it DOA?

The 12V power supply has 3 terminals for AC in: N, L and earth ground. The output of the 12V power supply has 2 DC + and - terminals. Cut the connectors off of the ends of the fan and pump wires. Strip the red and black wires of both units. The fan will connect to the 12V power supply red to the + and black to the -. The pump will connect in the same way, but the white is not connected.

Additional Information:

Click the link to add information to this solution:
I purchased the spindle cooling kit with power supply. and was wondering if you have a diagram on installing or a video. thank you

As shown in the instructions the laser tube that was used was a different model which had the metal end, compared to our full glass tube models we currently ship with the machines.
So there is no difference besides appearance between the two tubes.
The focus lens should be placed in the laser nozzle assembly and not on the laser tube itself.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I bought a blacktooth laser from you about a year ago.. I am finally getting around to installing the laser tube and I noticed that my tube does't have the metal end on it like all the pictures I've seen. is this a focus lense and can I purchase one?

Sure, let me check.

Additional Information:
Your order was shipped out on Tuesday (10/20/2020). I noticed that your email was not stored in the customer record when the order was made. I will send you the tracking number via email now.

Click the link to add information to this solution:
Placed an order for the cable set for the Pokeys57cnc interface on 10/20 but it is not showing up in My Account as being ordered. It was charged to my credit card and I have not had any info that it was received by you.

It is likely that if your Spindle's collet is ER11 specification than other size ER11 collets will work with your spindle.

Click the link to add information to this solution:
I bought a 1.5kw spindle that came with the ER11 6mm collet. I found collets for 1/4" and 1/2" but will these work with my existing nut? I see there is a nut for sale but it says its just for Bosh and Porter Cable etc.

If you want speed control, it is recommended to use the RS-485 connection on the VFD and use the control program such as Mach3 to communication serially with the VFD using this RS-485 connection.

If you would rather use a controller such as the PMDX-107 to simulate the effect of a potentiometer using the Aref, Aout and Agnd and the Rev/Dir and Fwd/Run terminals to control operation and direction, you can connect those to the VFD.

PMDX-107 Aout connects to the VI (analog voltage in). This is like the wiper on a potentiometer.
PMDX-107 Agnd connects to the ACM terminal on the VFD for Analog common.
PMDX-107 COM connects to DCM terminal on the VFD for Digital common.
PMDX-107 Fwd/Run connects to the FOR terminal on the VFD for Forward.
PMDX-107 Rev/Dir connects to the REV terminal on the VFD for Reverse.

Refer to your PMDX-107 manual to correctly configure your dip switch settings and make sure to calibrate (tweak) the speed control using the trimmer next to the terminals on the PMDX-107.

Click the link to add information to this solution:
I purchased the 4.0kw spindle and VFD a while back, and have just installed a PMDX-107 controller... do you have any examples of the wiring connections for the SL-240EE to PMDX-107?