Can you check if there are cracks in the inner glass tube? Also, check to see if there is water between the inner glass tube and the outer glass tube. That will give you an indication of cracking in the inner glass tube.

Click the link to add information to this solution:
I was in the process of aligning mirrors for our vertical XL and suddenly the laser does not fire anymore, there is an arcing sound and a light near the Anode (positive) connector of the tube on the very inside. Do you think the laser tube would go bad so quickly? how could we avoid this?

A CO2 laser will not be suitable for cutting steel. You would likely need a very powerful fiber laser to cut steel, and even then you have to take into consideration the reflective properties of steel which can pose danger to the machine.

Click the link to add information to this solution:
Trying to cut 24, and 26 G steel sheets in various shapes. Will CO2 laser be enough? And will it cause alot of heat in the product?

Are you using a laser controller?

Additional Information:
Had this same issue with a thunder laser. It turned out to be a simple check box setting in the software. I can't remember exactly, but I think it's was the mhz.

Click the link to add information to this solution:
My laser fires when traveling to its origin positon after finishing the job. Also once turned on , it will fire all the way to where it was before it was turned off.

When you power up your VFD, you can go into the programming mode by pressing the program button. You can press the up and down arrows to move through the parameters. Press the set button to go into the parameter to see the value of that parameter. If you want to make changes to that parameter, change the value with the up and down arrows until the desired value is shown, and press the set button to accept the changes.

Click the link to add information to this solution:
I AM HAVING TROUBLES FINDING THE PD PROGRAM, HAVE BUT IT DOESN'T SHOW EVERYTHING NEED TO PROGRAM MY VFD. ANY HELP WILL BE APPRECIATED...

Everyone always assumes they are doing something wrong when a plant fails to perform to their expectations. Grapes need pollinator activity to set viable fruit, but there is a shortage of bee activity throughout the country. When the flower cannot be pollinated by bees, the resulting fruit usually atrophies. It is not your fault, just a shortcoming in nature's network.

Click the link to add information to this solution:
I PLANTED SEVERAL CONCORD GRAPE VINES DURING THE PAST FEW YEARS. GOT A COUPLE OF VERY TINY BUDS THIS YEAR, BUT THEY DRIED UP AND DIED. WHAT AM DOING WRONG?

The Honeywell brand goggles meet ANSI certification Z136.1, relating to the safe use of lasers, and are calibrated to optimally block the specific wavelengths of light produced by CO2 lasers (the details are available in the website description here: https://buildyourcnc.com/item/laser-components-goggles-safety-honeywell.) The generic tinted goggles also block the specific CO2 laser wavelengths, but a good deal of other wavelengths as well. That and frame style variation is the basic difference.

Click the link to add information to this solution:
What is the difference between the tinted laser goggles and the Honeywell laser CO2 goggles

When you power up your VFD, you can go into the programming mode by pressing the program button. You can press the up and down arrows to move through the parameters. Press the set button to go into the parameter to see the value of that parameter. If you want to make changes to that parameter, change the value with the up and down arrows until the desired value is shown, and press the set button to accept the changes.

Click the link to add information to this solution:
[77] I am having troubles finding the PD program, I have the Pd but it doesn't show everything I need to program my VFD. Any help will be appreciated...

We are developing a 4 foot by 8 foot (48" x 96") laser with 80 watts of power. If you need a laser at 36" x 52", you could use the 4'x8' laser and just build a shorter table. We will have this machine available in the latter portion of 2015.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hello, I'm wondering if you could make a larger laser cnc if someone asks for it? Something like 36" x 52". And how much would it be?

In our 3-Axis electronics kit, the power supply's provided are capable of both 110V-220V. You have the capability to switch between both in case you might decide to run 220v in the near future or will relocate where 110v is being used.

Additional Information:
Connect spindle to the board



Additional Information:



Additional Information:

Click the link to add information to this solution:
In the 3 Axis Electronics Combo, what is the AC input of the power supply (110v or 220v??). is it possible to specify a certain voltage when ordering?

Is the cable between the mach3 USB and the YL260 shielded. If that does not solve the problem, add an induction coil to the cable to reduce any current fluctuations.

Click the link to add information to this solution:
Hello. I have bought an RnR Motion Controller and a YL260-A and I have it set up to the AVI from RnR to the VI1 of YL620-A but I'm getting that the RPM varies not like interference but like a drop from max value to min value. What could be happening?

The Honeywell brand goggles meet ANSI certification Z136.1, relating to the safe use of lasers, and are calibrated to optimally block the specific wavelengths of light produced by CO2 lasers (the details are available in the website description here: https://buildyourcnc.com/item/laser-components-goggles-safety-honeywell.) The generic tinted goggles also block the specific CO2 laser wavelengths, but a good deal of other wavelengths as well. That and frame style variation is the basic difference.

Click the link to add information to this solution:
I was wondering what was the difference between the two pair of goggles you are selling for the blacktooth. The tinted laser goggles and the Honeywell laser CO2 goggles

The relay is only used for devices like routers, spindles, coolant, mist, etc. The relay works like an automatic switch and will allow current to pass when the relay is engaged.

Click the link to add information to this solution:
The relay doesn't have a A+ B - it has signal in god. 5v. / 0 S P. This has to go to my USB motion card wiring shows v+ goes to top of coil no number and comes out the bottom to #2 the relay I got from you is not that simple

When the z axis is going down, the laser turns on. When the z axis is going up, it turns off. The z axis directions is only a signal that is either 5v or 0v. That determines the direction. In vectric, you will need to set your machining operations with a very very small depth so the time it takes to get to its final depth is a very short time.

Click the link to add information to this solution:
AM NOT SURE HOW TO SET THE Z AXIS TURN ON/OFF LASER WHEN CREATE CODE. KNOW THAT ITS TYPICALLY Z-AXIS MOVEMENT DOES THIS - BUT YOU DONT SHOW ANYTHING HOOKED UP IN PLACE OF AXIS.

When you press the x-axis limit switch, does the LED emit light?

Click the link to add information to this solution:
I currently have my whiteant build complete. But when I go to print the 20mm x 20mm box I seem to be having issues. The Z axis does not seem to move. Also the X axis hits the limit and does not move of of it. What is the best way to trouble shoot this issue?

If you are getting the "Communicating Unsuccessful!" error when you are trying to communicate between LaserCAD and the AWC608 Laser Cutter and Engraver controller (after you have already tried installing the USB driver from the LaserCAD setup procedure), these are the steps you will need for a successful communication:

- Open the Device Manager window (right click on the start menu and select Device Manager)
- When you plug the USB cable from the AWC608 Laser Cutter Controller (USB Type B connector) to the computer, you should see a new item in the Device Manager, possibly under "Ports (COM & LPT)", or under "Other Devices". It may show as an item under "Other Devices", possibly FT245R and has an "!" in a yellow triangle.
- Download the latest FTDI drivers from: http://www.ftdichip.com/Drivers/D2XX.htm
- Unzip the files to a folder that can be easily browsed.
- Right click on the item that appeared in the Device Manager when the cable was plugged in between the Laser Cutter AWC608 controller and the computer.
- Click on update driver
- Select the procedure to manually install the driver and browse to the folder containing the FTDI driver and follow the step in the driver installation wizard.
- The item should now be located under the "Ports (COM & LPT)" and should be named "USB Serial Device (COM#)". The # will be the number you will use in the LaserCAD software.
- In the LaserCAD software, click the "Select Mode" at the far top right of the Laser CAD user interface.
- Make sure USB mode is selected.
- If the Machine name with the correct COM number is listed, select it and exit the dialog window. Otherwise, click on "Add" and fill in the details with the new COM number.

Additional Information:


Additional Information:
Communicating unsuccessful

Additional Information:
Communicating unsuccessful

Click the link to add information to this solution:
I get a "communicating unsuccessful" when using LaserCAD and the AWC608 Laser controller

A 400w laser tube will not be a simple swap of our laser tube in our blackTooth or our spindle/laser hybrid. The overall size factor of a 80w - 400w is greatly larger than our 40w laser tube and will be the biggest issue. You will have to completely modify our units to retrofit a larger tube, which might be more costly than expected as well as more time consuming.

Click the link to add information to this solution:
Can I attach a 400w CO2 laser tube to you units (for cutting Stainless Steel at 1/8") ?

If your axis shutters and will not move unless moved by another force, that sounds like your acceleration is set too high. Lower the acceleration until it works well, then lower it a bit more to have a margin of safety.

IF that didn't work, try swapping the X and Y drivers. That way you will pinpoint if the issue is the driver. If the proplem persists, then there may be an issue with the motor itself.

The X and Y drivers can be easily swapped by swapping only the motor wires.

- Remove the x-axis motor wires from the X driver.
- Remove the Y motor wires from the Y driver.
- Insert the X motor wires into the Y driver.
- Insert the Y motor wires into the X driver.

Now the Y-axis will move the gantry. Test the Gantry movement by moving the Y axis using the up and down arrow keys (mach3).

Click the link to add information to this solution:
X AXIS STEPPER MOTOR STALLS AND SHUTTERS WHEN COMING FROM A STAND STILL WON'T MOVE WITHOUT PUSH BY HAND. I TOOK THE CHAINS OFF SPUN FINE WITH OUT LOAD. HAVE CHAIN HOOKED UP CAN MACHINE BACK FORTH HAND, NO HANG UPS OR ANYTHING, BUT TRY TO IT DOESN'T JUST SPINS OUT. ANY SUGGESTIONS?

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Click the link to add information to this solution:
WHAT CAN ADD TO MY BLACKTOOTH LASER CUTTER MEASURE THE TIME OF USE?

Depth of Field. This is how far the focal point goes before re-expanding again. With a 2" lens, you have approximately 2-3mm of DOF. This means that you'll have 2-3mm of perfectly focused laser before it starts to re-expand again. If you have a 4" lens, you will have up to 7mm of DOF.

Additional Information:

Click the link to add information to this solution:
WHAT IS D.O.F OR DEPTH OF FIELD FOR THE BLACKTOOTH LASER AND LENS?