[ Log In ]
[ Register ]

Question #: 14996

Question: output will not work in windows 10

Current Solution

For both of the controllers that I recommend, the pokeys57CNC and the Mach3 USB controllers, will both work fine in windows 10. If you are using the Mach3 USB controller, confirm that the output in the ports and pins configuration is using port 3.

Respond:

Other Possible Solutions to this Question

  • will any of your software work with Windows 10

    Yes, all of the software we sell on this website will work on windows 10.

    Additional Information:
    I have a usb controller with JP-3163B 3.9 V is it able to work with mach 4 and windows 10

    Click the link to add information to this solution:
    will any of your software work with Windows 10

  • Can Mach4 run under Windows 10?

    Yes, Mach4 will work with windows 10.

    Additional Information:
    Can I use a dB 25 BB mach4 and widows 10 if not what’s the best solution

    Click the link to add information to this solution:
    Can Mach4 run under Windows 10?

  • will 220v vfd work on 110v outlet

    No, VFDs with an input voltage of 220v will only work on 220 volt mains.

    Additional Information:
    Yes.. it will work. Get a 110V single phase to 220V three phase VFD. Like the https://www.invertekdrives.com/variable-frequency-drives/datasheets/ODE-3-210058-1042.

    Click the link to add information to this solution:
    will 220v vfd work on 110v outlet

  • Help with loading mach3 usb interface board on Windows 10

    The Mach3 usb controller/interface has instructions and videos on this page:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    There is a 5 step process on that page to install the plug-in and the configuration xml file that is necessary for the proper functioning of the controller.

    The videos on that page also demonstrate in detail how to install the software, plug-ins, xml file and wiring and testing most of the features of the Mach3 USB interface.

    Hope this helps.

    Click the link to add information to this solution:
    Help with loading mach3 usb interface board on Windows 10

  • Help with loading mach3 usb interface board on Windows 10

    The Mach3 usb controller/interface has instructions and videos on this page:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    There is a 5 step process on that page to install the plug-in and the configuration xml file that is necessary for the proper functioning of the controller.

    The videos on that page also demonstrate in detail how to install the software, plug-ins, xml file and wiring and testing most of the features of the Mach3 USB interface.

    Hope this helps.

    Click the link to add information to this solution:
    Help with loading mach3 usb interface board on Windows 10

  • Help with loading mach3 usb interface board on Windows 10

    The Mach3 usb controller/interface has instructions and videos on this page:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    There is a 5 step process on that page to install the plug-in and the configuration xml file that is necessary for the proper functioning of the controller.

    The videos on that page also demonstrate in detail how to install the software, plug-ins, xml file and wiring and testing most of the features of the Mach3 USB interface.

    Hope this helps.

    Click the link to add information to this solution:
    Help with loading mach3 usb interface board on Windows 10

  • WILL THE USB BREAKOUT BOARD WORK WITH MACH3?

    Sure, the USB interface has a place for 4 axes of limit switches.

    Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

    A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

    Let me know if this information was helpful (or not) by adding information to this question. Thanks.

    User response:
    Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
    Thank you.

    buildyourcnc response:
    On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

    Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

    In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

    There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

    Click the link to add information to this solution:
    WILL THE USB BREAKOUT BOARD WORK WITH MACH3?

  • [410] will this 4th axis work on laguna 1q cnc

    The Laguna 1Q has 154 mm of gantry clearance which is enough to clear the 100mm chuck and base of the 4th axis.

    Click the link to add information to this solution:
    [410] will this 4th axis work on laguna 1q cnc

  • WILL THE LASER ENGRAVER WORK ON NON-ANODIZED ALUMINUM

    no, it will only work on anodized aluminum

    Click the link to add information to this solution:
    WILL THE LASER ENGRAVER WORK ON NON-ANODIZED ALUMINUM

  • Does Corel Draw support LaserCAD V8.10.21 as a plug-in using Windows 10?

    Yes, LaserCAD V8.10.21 supports the use of CorelDraw and the CorelDraw direct output. In Chapter 2 of the manual (link below) that focuses on the installation of LaserCAD. At the first part of the installation, you will be given a set of options including the LaserCAD installation and the installation of plugins for AutoCAD, Adobe Illustrator and CorelDraw. Remember that the CorelDraw plugin must be installed in the director of the CorelDraw software.

    In chapter 5, the manual will instruct you how to install the Manual Download Tool "AWCLaserCut" within the CorelDraw sofware using the Macros feature of CorelDraw.

    I hope this helps. Thanks!!


    http://www.sztrocen.com/uploads/soft/20190103/LaserCAD%20User%20Manual.pdf

    Click the link to add information to this solution:
    Does Corel Draw support LaserCAD V8.10.21 as a plug-in using Windows 10?

  • How to output 0-10V to AVI+AVI-?

    In the motor outputs, the spindle should be set to pin number 3. This is also the output terminal number 3 (O3). In Mach3: Select [Config], select [Ports and Pins], and select [Spindle Setup] page in the popup dialog box. In the Motor Control box, check Use Spindle Motor Output and select PWM Control.

    [Use spindle motor output] is checked, Mach3 will automatically enable the spindle motor output pin. Click OK when the pop-up happens that will say "Spindle Motor has now been enabled. Ensure you set its pinouts.

    Next, select the Motor Outputs tab. At the line where [Signal] is [Spindle], check [Enable], modify [Step Port] to "3", modify [Step Pin#] to "3", and specify O3 as Is the output terminal of the PWM.

    Press [OK] button to save. Connect the indicator (refer to the previous section) to O3 for debugging. When the program "M3"executed is, O3 output signal can be seen.

    The AVI+ and AVI- corresponds to the ACM and AVI terminals.

    Additional Information:
    In the answer setting, 0-24V is output to out3, but not to AVI+/ACOM.
    Of course, 10V is given to the 10V terminal of the board.

    Click the link to add information to this solution:
    How to output 0-10V to AVI+AVI-?

  • Why does Windows 10 block the RnRmotion.dill for Mach3 USB interface from being downloaded?

    Yes, Mach3 (the software profram) will work with Windows 7, and windows 10 when coupled with the Mach3 USB interface. If you intend to use the parallel port driver, stick with Windows 7 in 32-bit mode.

    Additional Information:
    Rnrmotion.dll is a dynamic link library which is very similar in function to an executable program, or app. Since a dll is executable, malicious code can be embedded in that type of file, so windows will automatically flag all files of this type. You just need to make sure you are downloading from a trusted source. The emotion.dll file on our site is clean, but still run run windows defender against it to make sure.

    Click the link to add information to this solution:
    Why does Windows 10 block the RnRmotion.dill for Mach3 USB interface from being downloaded?

  • Why does Windows 10 block the RnRmotion.dill for Mach3 USB interface from being downloaded?

    Rnrmotion.dll is a dynamic link library that is very similar in function to an executable program, or app. Since a dll is executable, malicious code can be embedded in that type of file, so windows will automatically flag all files of this type. You just need to make sure you are downloading from a trusted source. The emotion.dll file on our site is clean, but still, run windows defender against it to make sure.

    Click the link to add information to this solution:
    Why does Windows 10 block the RnRmotion.dill for Mach3 USB interface from being downloaded?

  • THE SEND MAIL IN CONTACT US PAGE OF BUILDYOURCNC.COM WEBSITE DOES NOT WORK. ALSO CALLED MAILTO:

    You will need to change the default attribute of the browser that you are using (i.e. Google Chrome, IE, Firefox).

    Instructions to change this default attribute:
    1. Click on the "start menu"
    2. Click on "control panel"
    3. Click on "programs"
    4. Click on "default programs"
    5. Click on "set you default programs"
    6. Select the browser that you would like to fix
    7. Click on "choose defaults for this program"
    8. Find where it says "mailto" and set that to the default that you desire.

    Click the link to add information to this solution:
    THE SEND MAIL IN CONTACT US PAGE OF BUILDYOURCNC.COM WEBSITE DOES NOT WORK. ALSO CALLED MAILTO:

  • When will the 2.2kw 110v inverter be in stock?

    It's actually difficult to say when we will get our 2.2kW 110v VFDs (Variable Frequency Drives) in stock. The problem of predicting inventory stock with fluctuating sales is a challenge, especially at the price we offer. Please consider the 220v VFD, even if a 220 outlet is needed to be installed. We have found that the 220v VFD units performance to be better than the 110v VFD units.

    Click the link to add information to this solution:
    When will the 2.2kw 110v inverter be in stock?

  • I intend to intall mach3 on Windows 10 OS. Will I need to install the USB Motion Driver RnRMotion.dll? I attempted to download this but it was blocked by Windows 10.

    Yes, Mach3 (the software profram) will work with Windows 7, and windows 10 when coupled with the Mach3 USB interface. If you intend to use the parallel port driver, stick with Windows 7 in 32-bit mode.

    Additional Information:
    Rnrmotion.dll is a dynamic link library which is very similar in function to an executable program, or app. Since a dll is executable, malicious code can be embedded in that type of file, so windows will automatically flag all files of this type. You just need to make sure you are downloading from a trusted source. The emotion.dll file on our site is clean, but still run run windows defender against it to make sure.

    Click the link to add information to this solution:
    I intend to intall mach3 on Windows 10 OS. Will I need to install the USB Motion Driver RnRMotion.dll? I attempted to download this but it was blocked by Windows 10.

  • WHAT ARE THE OUTPUT INVERTER (VFD) CONNECTIONS TO SPINDLE?

    U - Pin1
    V - Pin2
    W - Pin3
    Pin4 Dead

    Additional Information:
    My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    WHAT ARE THE OUTPUT INVERTER (VFD) CONNECTIONS TO SPINDLE?

  • DOES THE SOFTWARE WORK ON AN APPLE?

    There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
    I've also read good things about punchCAD: http://www.punchcad.com/
    Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

    CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

    Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

    Additional Information:


    Additional Information:
    EasyDNC for OSX
    www.dnc-x.com

    Additional Information:


    Additional Information:
    Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
    My email if needed is r1jastrzebski@gmail.com

    Additional Information:


    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:

    Click the link to add information to this solution:
    DOES THE SOFTWARE WORK ON AN APPLE?

  • DOES THE SOFTWARE WORK ON A MAC?

    There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
    I've also read good things about punchCAD: http://www.punchcad.com/
    Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

    CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

    Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

    Additional Information:


    Additional Information:
    EasyDNC for OSX
    www.dnc-x.com

    Additional Information:


    Additional Information:
    Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
    My email if needed is r1jastrzebski@gmail.com

    Additional Information:


    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:

    Click the link to add information to this solution:
    DOES THE SOFTWARE WORK ON A MAC?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.