Yes we now have HIWIN rails in stock.

Click the link to add information to this solution:
HIWIN RAILS IN STOCK

Yes, we sell collets for the porter cable 892

http://www.buildyourcnc.com/collets.aspx

http://www.buildyourcnc.com/item/router-colletnut-router-collet-nut
http://www.buildyourcnc.com/item/router-collet-er20-router-complete-collet-kit
http://www.buildyourcnc.com/item/router-collet-!5-er20-router-collet
http://www.buildyourcnc.com/item/router-collet-!25-er20-router-collet
http://www.buildyourcnc.com/item/router-collet-!125-er20-router-collet

Click the link to add information to this solution:
WE HAVE PORTER CABLE 892, WILL YOUR COLLETS FIT?

It usually takes about three years before you get a viable crop from young grapevines. We planted grapevines at a house we built in California and the first crop that actually had enough grapes that we could actually pick and eat them was three years later. We ate them as we left town on our way to the East coast and our new home. They were growing strong when we passed by the old house some 10 years later.

A few varieties of grapes produce in two years, such as Brianna and Seyval grapes.

The good news is that grape vines usually live between 50 to 70 years, depending on the variety.

Click the link to add information to this solution:
WHEN WILL MY GRAPES GROW?

You can begin offering vaccine as soon as vaccine becomes available. Early vaccination of children younger than age 9 years who are first time vaccinees can be helpful in assuring routine second doses before the influenza season begins.

Additional Information:
V

Click the link to add information to this solution:
WHEN SHOULD INFLUENZA (THE FLU) VACCINE BE GIVEN?

The collet in the 1.5 kW spindle is an ER-11 and cannot reach the 1/2" size. I would consider the 2.2 kW spindle instead.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT SIZE COLLET IS IN YOUR 1.5 KILOWATT SPINDLE?

No. In general, registration is voluntary. Copyright exists from the moment the work is created. You will have to register, however, if you wish to bring a lawsuit for infringement of a U.S. work.

Click the link to add information to this solution:
DO I HAVE TO REGISTER WITH YOUR OFFICE BE PROTECTED?

The HIWIN rails come with the same flange blocks that are sold individually.

Click the link to add information to this solution:
About your HIWIN rails. What Carriage block does the 78" rails come with, 2 flange or 2 with no flange?

Tinnitus . Learn to love it. No really you should see a doctor. Make sure. White noise will help you sleep when it gets loud.

Additional Information:
I learned, too late, that if a sudden loud event causes tinnitus, see an audiologist IMMEDIATELY. They can do something about it if addressed within a day or so.

Wear hearing protection...always. Loud noises trigger my tinnitus, and headphones and ear plugs (when out & about or at the movies, subway, etc) help tremendously. Mine are rated 33dB.

Click the link to add information to this solution:
WHAT CAUSES RINGING IN YOUR EAR AND HOW CAN YOU STOP IT?

The plasma nozzle must be close to the cutting area and you will need some way to keep the nozzle at the right level with some type of device. The spray is downward, so you will need a contained area with a sheet of water at the bottom to extinguish he spray. You should have no problem using our machines for this application since you would need to product the table bed.

Click the link to add information to this solution:
CAN YOUR PRODUCTS OF MACHINES BE USED TO CREATE PLASMA TABLE?

BYCNC Response:
The book build was intended to be 20 inches x 40 inches. Larger machines were designed after the book build was introduced so customers would have the option to go bigger than what the book offered. Check out our larger machines on the website as the machines sizes range from 1 foot x 3 feet all the way up to 6 feet x 12+ feet.

User Response:
I'm not wanting to spend $3,000+ on a machine, I want to build one that will do a 4x8 sheet of wood. Will the plans in the book scale up?

BYCNC Response:
It is possible to scale the book build up, but the rigidity of the gantry would be questionable at that span, even if the height of the gantry structure were to be increased. The gantry design would need to be modified to become a box shape rather than a flat configuration. The kits on the site were design for those wanting a larger machine.

Click the link to add information to this solution:
I BOUGHT YOUR BOOK AND WAS HOPEING IT HAD PLANS OR DIMENTIONS ON HOW TO BUILD A CNC HOLD 4X8 SHEET OF PLY. WILL THE IN SCALE UP?

Try slowing your feedrate down and increasing spindle RPMs. End-mills will leave a poor finish if you go too fast. Make sure your cutting depth isn't too much. Maybe the endmill or cutter is blunt? Could it be the feed direction of the cutter? Some materials need to be fed in a certain direction.

Click the link to add information to this solution:
MOTOR GOING TWO DIRECTION WHEN JUST PUSH UP. IT WILL GO DOWN AND THEN GOES AGAIN UP WITH THE SAME BUTTON.

Yes, we sell rails with HIWIN specification. Our HIWIn spec rails are interchangeable with HIWIN brand rails.

Here is the link for our per inch product page.
https://www.buildyourcnc.com/item/mechanical-rails-HIWIN-Linear-20mm-Guide-Rail

Click the link to add information to this solution:
Do you sell the HIWIN rail sections without guide blocks?

Sure, the USB interface has a place for 4 axes of limit switches.

Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

Let me know if this information was helpful (or not) by adding information to this question. Thanks.

User response:
Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
Thank you.

buildyourcnc response:
On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

Click the link to add information to this solution:
WILL THE USB BREAKOUT BOARD WORK WITH MACH3?

Select the desired rail here:
https://buildyourcnc.com/Item/mechanical-rails-HIWIN-Linear

On the product page, enter the total "cut to order" length (in inches). Then call us to specify the cut lengths. Remember that our maximum length is 2000mm or 78.74 inches.

Our phone number is located at the top right of each web page by hovering over the "Need Help?".

Click the link to add information to this solution:
how do I order multiple lengths of HIWIN guide rail with blocks?

It is out of stock at this time (12/14/2018). We are awaiting shipment.

Additional Information:
The rail is now back in stock.

Click the link to add information to this solution:
HIWIN Rail out of stock

I can't think of any reason that it would be dangerous. However, I checked with the Cellular Telecommunications Industry Association. The Chairman of the Association sent the following memo on 18 June 1999, to the Associations' Board of Directors and others:
"You may have received inquiries about wireless phones causing fires or explosions at gas stations. In particular, you may have been asked about an alleged explosion at a gas station in Indonesia. We have been unable to verify any such occurrence in Indonesia or anywhere else. Moreover, in our discussions with Shell Oil they have stated they have attempted to verify these reports and also have not been able to document any such occurrence."
Nonetheless, in an abundance of caution, some manufacturers have included language in the owner's manuals for their products that recommends wireless phone users turn off their phones while at refueling points (gas stations). In addition, we have received information that Exxon will begin issuing warning signs at all domestic gas stations advising drivers to turn off all wireless communications devices when entering Exxon gas stations.

While wireless phone owners should always consult their owner's manual for information on the use of the phone, we are not aware of any incident that would justify these concerns."

Gen Roessler, Editor
HPS website

Click the link to add information to this solution:
WILL CELL PHONES SPARK A FIRE AT THE GAS STATION?

There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
I've also read good things about punchCAD: http://www.punchcad.com/
Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

Additional Information:


Additional Information:
EasyDNC for OSX
www.dnc-x.com

Additional Information:


Additional Information:
Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
My email if needed is r1jastrzebski@gmail.com

Additional Information:


Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:

Click the link to add information to this solution:
YOUR CNC SOFTWARE COMPATIBLE WITH MAC?

We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

Click the link to add information to this solution:
DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

Click the link to add information to this solution:
DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?