I use a standard large "L" square used in construction. I run gantry up and down with the bit along one side of the square to make the square aligned with the x-axis. I then run the bit along the other edge and if I see space from the edge of the bit to the square, I adjust the gantry square by loosening and tightening the eye bolts that hold the chain at the ends of the table. Repeat as necessary to get the desired square.

Additional Information:

Click the link to add information to this solution:
HOW DO I SQUARE MY CNC MACHINE OR GANTRY?

Nema 23 stepping motors with 100 oz-in rated holding torque and 1/4" shaft.

Click the link to add information to this solution:
WHAT MOTORS DOES THE BLACK TOOTH USE?

Nema 23 stepping motors with 100 oz-in rated holding torque and 1/4" shaft.

Click the link to add information to this solution:
WHAT MOTORS DOES THE BLACK TOOTH USE?

The blackTooth build instructions explain how to hook the four LED control panel to the USB breakout but not the Parallel BOB. Turns out it's very easy. Simply wire the corresponding LED cathodes (top pins on the display) to the matching CP- for the X, Y, and Z axises and wire the anodes (bottom pins) to the 5V terminals. For the on/off LED, wire the cathode to the G terminal on the laser power supply and the anode to the 5V laser supply terminal. Also, remove the 5V wire running from the Parallel BOB to the 5V terminal on the laser power supply. It is not needed and will cause the laser on/off light to always be on if the USB cable is connected.

Click the link to add information to this solution:
WIRING THE BLACKTOOTH LED PANEL TO PARALLEL BOB

You get the plans for this machine:
http://www.buildyourcnc.com/cnckitintro.aspx

Additional Information:

Click the link to add information to this solution:
IF ORDER 'COMBO #1 (PLANS WITH DVD)', WHAT PLANS DO GET?

The stamps.com technical support is developersupport@stamps.com

Click the link to add information to this solution:
WHAT THE TECHNICAL SUPPORT FOR STAMPS.COM?

The base greenLean CNC Machine Kit package includes:
- Structure (all of the structural parts that make up the gantry and rib system). The structure does not include the spoilboard.
- Hardware (All of the fasteners, like screws, nuts, cross dowels, washers, etc.)
- Mechanical components (bearings, rails, sprockets, shafts, etc.)
- Electronics (3 NEMA 651 Motors, 3 6.0 Amp drivers power supply, interface card to connect the drivers to a computer, and 91 feet of motor cable. Hookup wire to connect the electronics is not included.)
- 2.2kw Spindle and VFD

Here is a link to the greenLean CNC Macnine page: https://www.buildyourcnc.com/item/cnc-machine-greenLean-v1

Click the link to add information to this solution:
WHAT COMES IN THE BOX FOR BASIC GREENLEAN?

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HOW MUCH MOTOR CABLE FOR THE BLACKFOOT?

The total length of the brush strip for a 2.2kW spindle would be 17 1/4" inches.

Additional Information:
20

Click the link to add information to this solution:
LENGTH OF THE BRUSH STRIP FOR SPINDLE 2.2KW

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

The blackfoot requires a total of 50 feet of cable.

The X axis needs 15 feet
The Y axis needs 17 feet
and the Z-axis needs 18 feet

These are 20 gauge 4 conductor cable.

Additional Information:

Click the link to add information to this solution:
MOTOR 4 CONDUCTOR CABLES FOR BLACKFOOT

Under Connection -> Serial, configure the correct settings for the data frame

Under Session, select Serial, the serial line "com" and speed should reflect the information set in the connection -> serial.

Click the "Open" button to start the communication.

Additional Information:

Click the link to add information to this solution:
HOW DO START PUTTY FOR SERIAL COMMUNICATION?

Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.


Link:
https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

Click the link to add information to this solution:
WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

Under Connection -> Serial, configure the correct settings for the data frame

Under Session, select Serial, the serial line "com" and speed should reflect the information set in the connection -> serial.

Click the "Open" button to start the communication.

Additional Information:

Click the link to add information to this solution:
HOW DO SET UP PUTTY FOR SERIAL COMMUNICATION?

Vines are normally planted bare root from January to March and spaced 7 to 8 feet apart in rows 10 to 12 feet apart. Vertical stakes or posts with 1 or 2 wires on the side, or with “T” tops with wire are desirable supports for grapevines. Cane prune Thompson seedless and Concord. Spur prune other varieties. Frost (31oF) damages new shoots and fruit clusters in April or May, so plant where the frost is minimized. Spraying or dusting sulfur for mildew is necessary on wine and table grapes, but rarely needed with American types. (From http://ucce.ucdavis.edu/files/filelibrary/40/935.pdf )

Click the link to add information to this solution:
HOW SHOULD I CARE FOR MAY GRAPEVINES?

The roller chain lengths for the greenBull 4x is:
- 13 feet for each side of the X axis (total of 26 feet), and
- 6 feet for the Y-axis

Click the link to add information to this solution:
ROLLER CHAIN LENGTHS FOR GREENBULL 4X

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKTOE