TIR specifications for the ER-20 collet used on 2.2KW Spindles is .0004 inches.

Click the link to add information to this solution:
Hi, I'm considering buying one of your 2.2 KW water cooled spindles. What is these spindles run out ?

The following answer assumes "radio Base Station Antennas" refers to base stations used for personal wireless communications services such as cellular telephone, Personnel Communications Services (PCS), and Enhanced Specialized Mobile radio (ESMR). In the United States, the frequency band allocated for base stations used for personal wireless communications is 869-894 MHz for cellular service, 851-866 MHz for ESMR, and 1930-1990 MHz for PCS. The IEEE exposure limits (maximum permissible exposure—MPE) for occupational exposure (controlled environments where exposures may be incurred by persons who are aware of the potential for exposure) are frequency dependent and are expressed in terms of incident power density. The appropriate value to compare with the MPE is the incident power density averaged over the vertical cross-section of the human body. The occupational exposure limits are also time-averaged over any six-minute interval. The IEEE C95.1-1991 MPE values are shown in the table below:
IEEE C95.1-1991 Maximum Permissible Exposure (MPE) Values
Frequency Band Power Density
General mw/cm2 W/cm2
851-866 MHz f/300 mW/cm2 2.84-2.88 28.4-28.8
869-894 MHz f/300 mW/cm2 2.90-2.98 29.0-29.8
1930-1990 MHz f/300 mW/cm2 6.43-6.63 64.3-66.3
NOTE: f is in MHz
As indicated above, these values are for continuous exposure (t > 6 minutes) and are to be compared with the spatial average of the incident power density. all base stations used for personal wireless telecommunications services in the United States are required to comply with the FCC limits (as mandated by the Telecommunications Act of 1996). The FCC limits are based on a hybrid of the IEEE limits and the 1986 recommendations of the National Council on Radiation Protection and Measurements. The FCC MPEs are the same as the IEEE values for frequencies below 1500 MHz but are capped at 5 mW/cm2 (50 W/cm2) for frequencies greater than 1500 MHz.

Both the FCC and IEEE MPEs for exposure of the public (uncontrolled environments) are one-fifth of the above values. As above, the value to compare with the MPE is the incident power density averaged over the vertical cross-section of the human body. The averaging time for the general public is 30 minutes. Thus, for transient exposures lasting six minutes or less, the MPEs for occupational exposure and exposure of the general public MPEs are the same. For cases of simultaneous exposure from antennas operating in different frequency bands, the ratio of the spatially averaged incident power density in each frequency band to the corresponding MPE for that band is determined and the sum of all such ratios must be less than unity in order to comply.

R. C. Petersen
Manager, Wireless and Optical
Technologies Safety Department

Click the link to add information to this solution:
WHAT ARE CURRENT RECOMMENDED IEEE EMF OCCUPATIONAL EXPOSURE LEVELS AND GUIDELINES FOR RADIO BASE STATION ANTENNAS?

The lens is 20mm wide and a 50.6mm focal length (the one included). This lens will stand up to at least 30PSI air assist.

The mirrors are 25mm wide mirrors.

Focal length is the distance from the lens to the material for the laser converge into the best focal point. If a lens is listed as 2". You measure 2" from the lens to the material, this will be the tightest point the laser can go before it starts to re-expand again losing focus.

Click the link to add information to this solution:
WHAT ARE THE BLACKTOOTH LENS SIZES AND FOCAL LENGTH SPECIFICATIONS?

The 2.2kW spindle outputs approximately 3 HP (Horse Power).

Click the link to add information to this solution:
What is the HP of the 2.2KW spindle

There is very little radiofrequency (RF) energy exposure to people inside a building from a cellular base station located on its roof. There are several reasons for this. First, the transmitters operate at low power levels. Second, the antennas are normally mounted near the edges of the roof and are aimed away from the building. Third, most cellular transmitters use "high gain" or panel antennas. Such antennas transmit most of their energy in a narrow beam (in the vertical direction) from their front surfaces, away from the building. They radiate very little energy downwards towards the roof or backwards from their rear surfaces. Finally, building materials absorb a significant fraction of the RF energy passing through them. As a result, the RF signal levels at any location inside the building are invariably low and far below safety limits. The situation might be different in some locations on the roof itself. RF signal levels close to (within a few feet) and directly in front of cellular base station antennas can easily exceed safety limits. Some precautions are needed to prevent people from walking directly in front of the antennas while they are transmitting. This applies also to paging and other systems that use rooftop antennas, some of which transmit at higher power levels than many cellular base stations. Kenneth R. Foster, Ph.D.

Click the link to add information to this solution:
WHAT ARE THE HEALTH RISKS OF LIVING NEAR A CELL PHONE TOWER?

The runout on our 2.2kW spindle and number of bearings are:
Radial runout: 0.01mm - 0.000393701 inches, 3 Bearings


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
What is the runout on the 2.5 KW spindle and how many bearings?

Yes, all of the spindles come with collets. The collets have a 1/4" (6.35mm) bore for end mills that have a 1/4" shank. The ER specification is different for the 1.5kW (ER-11) and the 2.2kW (ER-20).

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I’M LOOKING TO PURCHASE SPINDLE AND VFD WAS CURIOS IF THE SPINDLES COME WITH COLLETS SO WHICH ONES?

Depth of Field. This is how far the focal point goes before re-expanding again. With a 2" lens, you have approximately 2-3mm of DOF. This means that you'll have 2-3mm of perfectly focused laser before it starts to re-expand again. If you have a 4" lens, you will have up to 7mm of DOF.

Additional Information:

Click the link to add information to this solution:
WHAT IS D.O.F OR DEPTH OF FIELD FOR THE BLACKTOOTH LASER AND LENS?

The 2.2kW spindle has a power rating of 2.2kW or 2200 watts.

If the VFD AC voltage input is rated for 220 volts, then 2200 watts / 220 volts is 10 amps, so a 15 or 20 amp breaker will work.

If the VFD AC voltage input is rated for 110 volts, then 2200 watts / 110 volts is 20 amps, so a 25 or 30 amp breaker will work.

Additional Information:



Additional Information:

Click the link to add information to this solution:
what size circuit breaker should I use with the 2.2KW VFD?

We honor a one year warranty on most parts like main machine components, structural parts, mechanical parts and some electronic parts including spindles.

Click the link to add information to this solution:
What is the warranty on your 2.2KW spindle

Shipping crate size 121" X 36" X 92"

Weight 511 LBS

Click the link to add information to this solution:
WHAT ARE THE SHIPPING DIMENSIONS FOR VERTICAL LASER

Lettuce, or any vegetable. Also drink a cup of water before meals, it'll make you feel fuller.

Click the link to add information to this solution:
WHAT ARE THE BEST FOODS THAT WILL HELP YOU LOSE WEIGHT?

The roller chain lengths for the greenBull 4x is:
- 13 feet for each side of the X axis (total of 26 feet), and
- 6 feet for the Y-axis

Click the link to add information to this solution:
WHAT ARE THE ROLLER CHAIN LENGTHS FOR GREENBULL 4X

You can expect a two week lead time for the redFrog pick and place machine.

Additional Information:

Click the link to add information to this solution:
WHAT IS THE LEAD TIME FOR REDFROG PICK AND PLACE MACHINE?

Shipping crate 121" X 36" X 92"

Weight 511 LBS

Additional Information:
ship in india pls

Additional Information:
International shipping rates can be determined by:
- adding products to the cart
- go to the cart and enter shipped by address
- and pressing the calculate shipping button

Click the link to add information to this solution:
WHAT IS THE SHIPPING WEIGHT AND DIMENSIONS FOR GREENLEAN?

U - Pin1
V - Pin2
W - Pin3
Pin4 Dead

Additional Information:
My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT ARE THE OUTPUT INVERTER (VFD) CONNECTIONS TO SPINDLE?

76" X 40" X 26"
230 LBS

Click the link to add information to this solution:
WHAT ARE THE SHIPPING DIMENSIONS FOR GREENBULL?

Standard Version Features Mach3 Mach4 Hobby Mach4 Industrial
Number of Planners 1 1 1
Number of Axis 6 6 6
Out of Band Axis (OBA) 0 1 6
Slave axis (uses up coordinated axes) 3 N/A N/A
Slave motors (does not use up coordinated axes) N/A 4 per Axis 4 per Axis
API Interface - Open to All Hardware Yes Yes Yes
Extended Plugin Support Yes Yes Yes
User customizable GUI Yes Yes Yes
Unified (GUI) Interface - PLC, CNC, etc.. Yes Yes
Unlimited IO Yes Yes Yes
Modbus PLC Yes Yes Yes
PMC (Ladder Logic addressing for cnc/plc) Yes Yes
Unlimited File Size Yes Yes
Tool Path Display Yes Yes Yes
Tool Path Speed & Quality Low High High
Scripting - Customization Yes Yes Yes
LUA Scripting - simple, fast, cross-platform Yes Yes
- Lua sockets (ftp, http, smtp,..) Yes Yes
- SSL (security layer) Yes Yes
- LFS (manage large files and data storage) Yes Yes
- Seriel port Yes Yes
- Enraving of part numbers / serial numbering of parts Yes Yes
- Plugin panel objects Yes Yes
IPC Library for Data Sharing/tracking (Interprocess communication) Yes Yes
Full Feature Screens/Controls Per Machine Type Yes Yes
Currently Availabe: Mill, Router, Lathe, 3d Printer Yes Yes
Multiple gcode Interpruters (Per Machine Type) Yes Yes
Probing - Intergrated in standard screens Yes Yes
Simulated 3d Machining (with additional plugin license) Yes Yes
Tool Life Management (G10 L3 command) Yes
Screw Mapping Yes
Professional Screen Designer (advanced G.U.I.) Yes
- Screen Animation Control Yes
- Screen Integrated Tool Table Control Yes
- Screen Integrated Work Offset Control Yes
- Screen Integrated gcode editor Yes
- Screen Artsoft Wizard Package Integration Yes
Macro B gcode Programming (#variables) Yes
- User definable gcodes via marco calls Yes
- Macro Calls: G65, G66, G66.1 Yes
- gcode via marco call (custom G codes via macro B) Yes
- mcode via macro call (custom M codes via macro B) Yes
- mcode via sub code (custom M code via sup program) Yes
- Conditional gcodes Yes
- set VN call - define variable names Yes
gcode Editor Included Yes
Scripted M code (custom M code via LUA script) Yes Yes
Variable Speed Spindle Yes Yes Yes
Spindle Relay Yes Yes Yes
Coolant relay Yes Yes Yes
Mist Relay Yes Yes Yes
Threading Yes Yes Yes
Rigid Tapping Yes Yes Yes
Single Block Yes Yes Yes
Block Delete Yes Yes Yes
Optional Stop Yes Yes Yes
MACH CNC CONTROL SOFTWARE MAIN FEATURES AND VERSION DIFFERENCES
Standard Version Features Mach3 Mach4 Hobby Mach4 Industrial
MACH CNC CONTROL SOFTWARE MAIN FEATURES AND VERSION DIFFERENCES
Cutter Comp Yes Yes Yes
Fanuc Type C Cutter Comp Yes Yes
Fixture Offsets Yes Yes Yes
G51 Scaling Yes Yes Yes
G92 Offsets Yes Yes Yes
G52 Offsets Yes Yes Yes
Event Driven Yes Yes
Multi Line MDI Yes Yes
Subs In MDI Yes Yes
OpenGL Optimization Yes Yes
Multi-platform OS Compatibility Option Yes Yes
Online Support Yes Yes Yes
Phone Support Option Available Yes
Support Priority Yes
Available to End Users as "Do-it-yourself" Yes Yes
Summary - Mach3 versus Mach4 :
Mach4 Hobby is the closest comparable version to Mach3, yet it is still much more advanced. The price point of these versions is nearly
identical. Mach3 is very popular for hobby enthusiest and is used in highly modified form by some great OEM's. In general, Mach4 is more
complex than Mach3 and follows cnc industry standards. Mach3 has many customizations to make it easier for hobby users, but can lead to
difficulties if users plan to apply their knowledge to more advanced systems. Mach4 is built as a full featured cnc controller capable of high
speed machining for servo and stepper systems. Mach3's feature set is complete, while Mach4's will continue to expand. If you are new to cnc,
Artsoft highly recommends using and learning Mach4 even if it appears that Mach3's feature set will be adequate for your needs.

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE BETWEEN MACH3 AND MACH4?

Input to VFD:
240V Active - R
240V Neutral - S
Ground - E

Additional Information:

Click the link to add information to this solution:
WHAT TERMINALS ARE USED TO CONNECT THE INVERTER WALL OUTLET?