Here is how to connect your router to the parallel breakout board through the on-board relay. You will need a spare extension cord. You will need to remove a portion of the outer jacket of the extension cord to expose the white, black and green wires (white = neutral, black = live and green = ground), understanding that the neutral and live create the completed circuit.

See this image of a similar connection. The terminal has the same connections.
https://www.buildyourcnc.com/images/vacuum-pressure-controller-relay-terminals-700.JPG

Image of the relay terminal:
https://www.buildyourcnc.com/images/breakoutboardrelayNONC.PNG

The live/black wire would be cut and one end of the cut would be secured into the P terminal and the other cut end would be secured into the S terminal. The live and ground wire would be uncut and travel from the plug to the router.


Additional Information:
You can also connect other high powered devices to the breakout board using any of the output terminals. You will need to supply extra relays like the one shown here:
https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Or you can find SSRs (Solid State Relays) that will accept 5v to drive the relay coil. Make sure the SSR will protect the 5V line from Back EMF as there is a coil in the relay. The one we sell contains a fly-back diode to protect the 5v terminal.

Click the link to add information to this solution:
I have your breakout board with relay parallel port , I have a vacuum, light on router and air pump I want to also hook up to board, can I hook those up to board and also could I had reylays to each one, what is the best way to figure this out any information would be great. Thanks

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

Yes, you can control the speed of the 2.2 kW spindle, and the other spindles we sell, through Mach3 software. It requires making some changes to the settings in Mach3 and in your inverter. It also requires an additional part, which is called a USB to Serial Converter, found on our site here:

https://www.buildyourcnc.com/item/Interfaces-newbiehack-Interfaces-TTL232R-USB-UART-Serial

I have some additional instructions, that I will send upon request, by email. I will also be adding a complete tutorial and video, to the website, on how to do this soon.

Additional Information:
20

Click the link to add information to this solution:
can I control the speed of a 2.2 spindle through your 5 axis breakout board with relay?

A parallel to USB adapter will not work. You will need to use a USB interface like the ones below:

Mach3 USB interface:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Poeys57CNC Interface:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Additional Information:
To answer the question in more detail, the parallel port is actually an extension straight from the CPU and is also called the GPIO (General Purpose I/O) pins. These pins carry signals independently, hence the description as being a parallel port.

The stepper motor driver receives a pulse train (series of pulses). A single pin on the parallel port sends a pulse train to one stepper motor driver and stepper motor for a single axis. Another pin on the parallel port sends a pulse train to another stepper motor driver on another axis. This happens simultaneously as with the direction signals for each axis.

If a parallel port is adapted through a USB (using an adapter), the parallel port cannot have these signals happen in a simultaneous fashion and will cause the stepper motors of a CNC router or machine to be very clunky, if it works at all. To elaborate, the computer sends an instruction to the USB to send a high signal to pin 1, so it does, then another signal to pin 2, so it does. This is happening one after another. The speed at which this happens is reduced dramatically, and the position of one axis may now be out of sync to another axis.

The reason the USB interfaces (linked above) work is that the USB delivers broad instructions to the interface (to a microcontroller) and the interface parses the instructions and outputs simultaneous signals to the stepper motor drivers.

Hope this helps.

Click the link to add information to this solution:
My computer doesn't have a parallel port connection. Can I use a usb to parallel port cable to communicate with my breakout board?

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I have your mach3 USB BoB, do you guys sell a torch control relay I can wire up to turn my plasma torch on and off and how I would wife that too this BoB?

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
I have a parallel. breakout board. and no parallel port at the back of my computer do those parallel. cards. work with the breakout board?

Sure, connect O2 (output #2) on your mach3 USB board to the GND side of your relay coil. Connect the 24V power supply to the positive side of your 24v relay.

You will want to connect a flyback diode (1N4007) between the coil connections to make sure the coil back current does not damage the Mach3 USB board.

Refer to this diagram:
https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf

Please let me know if this helps and if you need further guidance.

Thanks

Click the link to add information to this solution:
I recently purchesed a USB Mach3 breakout board and need help setting mach3 to use a relay to start the router can you show how to set the pins and which port to use on the board to attached the relay?

You can add a limit switch to either the USB or the parallel board. Please refer to the product pages for these items to view wiring diagrams.

Click the link to add information to this solution:
I want to add limit switches but I have no connections on the breakout board. Can I use a usb interface board for the limit switches as well as the parallel port for the running?

You can add a limit switch to either the USB or the parallel board. Please refer to the product pages for these items to view wiring diagrams.

Click the link to add information to this solution:
I want to add limit switches but I have no connections on the breakout board. Can I use a usb interface board for the limit switches as well as the parallel port for the running?

The 5V power required for the breakout board can be a simple USB male to male cable, that will connect from your computer to the board itself.
Now adding a external power supply make sure that it does not exceed a total of 5V and the standard 500 MilliAMP - 1 A.

Click the link to add information to this solution:
I have a YDH-18-5 Power Supply AC Input:100-240v 47-63Hz, Ouput: 5v - 2A and need to know if its safe to use with the Parallel Breakout Board.

Most motherboard do contain parallel ports, but the port connector may not be at the back (in the section where external connectors will be connected). Instead, the motherboard may contain an LPT ribbon connector on the actual face of the motherboard (usually along one of the edges). You will need a ribbon connector to a DB25 female connector.

If your motherboard does not contain an LPT header on the motherboard, you can purchase a parallel printer adapter that plugs into one of the PCI slots. The price of the adapter is very inexpensive and sometimes is actually less costly than the actual ribbon connector.

Click the link to add information to this solution:
As I am building my 20" x 24" laser engraver cutter, I notice that there is no parallel port on the onboard computer and I have the parallel breakout board any answers?

The USB port on the Parallel Interface board is necessary to supply 5V power. Connect with a USB cable to a USB source.

Click the link to add information to this solution:
I purchased a parallel port breakout board. I have checked all the info and found nothing on the usb port. What is it used for?

We are currently working on a relay board that will connect to USB breakout board, and the router/spindle for both the on/off function. Unfortunately we still do not have it completed or ready to be placed on our website, but it is in the final stages of testing. Please check back regularly for updated stock!

Here is a link to a tutorial for a DIY relay circuit:

Click the link to add information to this solution:
I AM PUTTING TOGETHER THE BLACKFOOT AND USING A PORTER CABLE ROUTER. CONFUSED ON HOW TO RELAY ROUTETR WITH USB BOARD. IS THERE ANOTHER SWITCH THAT GOES BETWEEN BOARD ROUTER SO PLANET CNC CAN TURN PERHAPS VACUUM OFF?

Does your plasma cutter have an external trigger that voltage can be applied to make the trigger engage? If I known, please provide the brand and model of your plasma cutter so we can determine this.

Additional Information:
I converted my blackToe to do plasma cutting. Used the Motor control relay on the break out board and just wired it into the plasma cutter trigger. Put a large pan (like a car oil drip pan) with about 1/4 inch of water on the table and attached fixtures. 400 15ga parts later it's still working great.

Additional Information:
That is so cool!!

Additional Information:
I would like to post a story on your setup and conversion. Do you have pictures of the process and/or the new setup?

Click the link to add information to this solution:
Hello I bought a full setup of parts a couple years ago to make a cnc router and now I have decided that I want to make a cnc router/plasma. I was wondering how to go about hooking up the plasma to the breakout board

Yes, the 5 axis breakout board is a very suitable replacement and also contains a relay for spindle/router control which is not on the C10 board.

Click the link to add information to this solution:
I have propably blown my C10 breakout board. This is no longer available in your parts list. Is the 5 Axis Breakout Board with Relay a suitable replacement?

The parallel breakout board contains a USB port to power the board. Through the USB port, the computer delivers 5v of stable power to the parallel breakout board, but doe not provide any communication as would normally be associated with USB connectivity.

The reason we elected to use the USB port to provide power is to remove the need for an external 5v wall adapter.

Click the link to add information to this solution:
Does the Blue Brew breakout board require 5v to be supplied from a USB cable, to pass parallel port outputs to its terminals?

You can find instructions for the Mach3 USB here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

You will probably need to use the Mach3 USB board with Mach3. We have not tested the Mach3 usb card with Mach4.

Click the link to add information to this solution:
Whereb can I find directions on how to install the Mach3 USB board with Mach 4 software? I do not have a parallell port.

The USB on the Parallel breakout board, is used for powering the board itself (5v USB), and the Parallel to communicate directly between the drivers and the computer/mach 3.
Planet-CNC cannot be used with our Parallel Breakout Board, it is only intend to be used with Mach 3/other open source programs.

To use Planet-CNC, please refer to our USB breakout board! (https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout)

Click the link to add information to this solution:
can I use the usb on the parallel breakout board with planet cmc