Considering enlarging the machine, might have its down sides do to the structural integrity of the scratch build machine. Primarily by making the width longer it will start to sag in the center, which will lead to having to redesign the gantry to be more structurally rigid to support the added length. Which then will increase the weight and height of your gantry to support the add size, which will always end up to creating a larger CNC.

We usually do not recommend modifying the scratch build CNC, due to the very limited capabilities, and the structural design of the scratch build. We also do not recommend using longer than 48" ACME screw/leadscrew due to the increasing chance of warping and bending in the ACME screws/leadscrew in the given length.
We do recommend modifying the CNC machines we sell to accommodate the added requests that some of our customers desire, but you will be limited to the width of the gantry with our machines.

Click the link to add information to this solution:
I've read your book and I'm looking to purchase the hardware kit with DVD as well as an electronics kit. I would like my machine to have a working area of at least 24" wide by 48" long. Can I just make the bed (and gantry) wider to accommodate larger priceslike 30"x60"? If so what electronics kit would you recommend?

What material is the 0.1mm and 0.2mm board?

Additional Information:
Steel sheet


Additional Information:
Steel Sheet

Additional Information:
Thanks for the response. CO2 lasers unfortunately cannot cut metallic materials. Metals are best cut with other types of lasers, or by using oxygen assist. The oxygen assist method is not encourages as the combination or CO2 laser and oxygen is very volatile.

Additional Information:
and I can not do this laser to cut the steel plate, but instead of the CO2 tube I put the oxygen tube, or do not I know ?! Do I have a chance in the products on the site to create a laser for 0.1mm and 0.2mm steel sheets?

Additional Information:
I can help with an answer, Thanks!

Additional Information:
I can help with an answer, Thanks!

Additional Information:
Can you help me with an answer? Thank you! **

Click the link to add information to this solution:
If I build a Laser with the components on this site, can I cut the 0.1mm and 0.2mm board? Is it cut in optimal conditions, or if not what you recommend ?!

Consider the loads on each axis when choosing appropriate stepper motors. If your holding torque is maxed out at roughly 16oz/in (1lb/in), then you could use the NEMA 11 or 14. Also consider the shaft sizes and current ratings when choosing drivers that pair with the motors.

Click the link to add information to this solution:
I am planning to build a scratch CNC machine to do rotary engraving on writing pens. Can you recommend the parts I would need? I'm thinking NEMA 14 (11?) and 3/8" acme rod. Not sure which linear motion to use. I have an old lathe to use for the 4th axis.

Depending on the type of motors and connection type, you could adapt your motors to work with our electronic packages, but you will receive additional motors since our kit is complete.

Now you will have to take into affect the actual motors you have and compare or get accurate replacements(Ex. our 425 oz motor(1/4" input shaft) will have to be same size or similar entry holes)

Your Controller board will be the major issue, due to its wiring and processing manner, you can view the connections for our breakout boards to compare with yours! (parallel: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/)(USB: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/)
Email(customerservice@buildyourcnc.com for further help)

Click the link to add information to this solution:
I am looking at one of your electronics packages as a replacement for my excisting electronics. I have a old table top CNC that has a bad electronics pack, but the motors, and the mill are in good shape. could your system be adapted to work in this case?

Attaching two motors in parallel is possible, but you will need another motor and driver for the opposite side. Each motor must have its own driver to work accordingly and fluently. The two can be wired together, to the same pins on your breakout board and set the dip switches on the driver to match the ones on your x-axis(ex). But remember to view the orientation of the motor and which way it spins, since it is on the opposite side it will have to be orientated correctly to move in sync with the other motor.

Click the link to add information to this solution:
I just finished building my first CNC with the electronics I purchased from you and I am already thinking about improving it. I would like to build a 2 motor X axis solution. Is it possible to attach 2 parallel motors and drivers to the BlueBrew Breakout Board? If so, how?

We recommend our electronics combo for the scratch build kit, which you can find on our site here: https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo. This is our standard general purpose 3 axis electronics system, and includes (3) NEMA 24 425 oz-in stepping motors, (3) Drivers (3.0Amp 24-40 Volts, with 1-1/64 microstepping), (1) 36v 8.8a Power Supply, (1) Interface Board either USB or Parallel. (The USB version requires PlanetCNC software; the parallel interface board gives you a variety of options, Mach3 being one popular choice.)

Click the link to add information to this solution:
I am going to build a CNC 4x4 plasma table. The frame is made of 1 1/4" pipe and the gantry will be made of either 2"x 2" or 2"x 3" tubing. What size stepper motors do you suggest?

The dimensions for the #40 drive sprockets will be 1.835" radius tooth to tooth , .575" from teeth to teeth, 0.600" / 3/5 ID, 1.249" OD.
Now the idler sprocket dimensions (same format):
Radius ttt: 2.963"
Fttt: 0.535"
ID: 0.600" / 3/5
OD: 0.825"

Click the link to add information to this solution:
I am designing/building a cnc plasma cutter and I would like some info on some of your parts. Would it be possible to get dimension and/or drawings (or models) of the #40 drive and idle sprockets?

The drivers have quite a bit of protection, so you probably won't ruin anything. You motors are jumping and that is just the motors engaging from getting power from the power supply.

There could be many reasons your motors don't turn. Consider these troubleshooting tips:

- If you are using our parallel breakout board, make sure that the step pins are set for active low (config -> Ports and Pins -> Motor Outputs -> the steps pins should be enabled and set active low)

- The parallel breakout board is powered (connect the USB to the computer using a USB cable)

- In Mach3, make sure you have jog enabled (a little green button at thelower middle of the page in the program run screen).

Additional Information:


Additional Information:
DS26

Click the link to add information to this solution:
If I wired my stepper motors incorrectly what parts of the electronics will be ruined? When I turn on the power, my motors jump like they are supposed to but for some reason, the G-code doesn't seem to be moving from Mach 3 to the motors. Any help would be appreciated. Do I need to order new electronics or just part of the system? Thanks

The best machine due to the width, will be the greenBull 5x which would have a cutting surface of 5' x 10'. Also our machines with spindle are accurate for 1000's of an inch, and can do 45 degree angle cuts.

Click the link to add information to this solution:
I build custom speakers and I work primarily with 5'x5' sheets of 9 ply (1/2") and 13 ply (3/4") plywood, but I occassionally cut 2" nominal thick wood as well. What kit would you recommend? Are your systems accurate enough to do angle cuts (45 deg?) thanks

The files and hardware option for our machines has been removed from the site due to the following reasons:
Difficulty for the end use of the files and the challenges (and time/money) on our side to assist in using these files.
The abuse of these files over the internet.
Ultimately may reduce the sales of machines keeping us in business.
Sadly, this is what has come out of our company attempting to be open; however, the machines sold on this site is still far lower in price than the competition for the quality that we provide as we have a great desire to engender the cottage industry to fulfill their need for low end manufacturing. My sincere apologies if this causes any inconvenience.

Additional Information:
NO, is not possible, I can help with the shipping cost

Additional Information:

Click the link to add information to this solution:
IT POSSIBLE TO BUY THE CAD FILES FOR BLACK FOOT MACHINE, MECHANICAL PARTS AND ELECTRONICS BUT NOT WOODEN PARTS, SAVE SHIPPING COSTS? IN THAT CASE I WOULD INSTRUCT SOMEONE MILL ME.

Sure, email me at customerservice@buildyourcnc.com and I will send you a replacement for a minimal fee. I now use HDPE for that part. The HDPE holds up much better.

Click the link to add information to this solution:
I have a Blackfoot 4x4 v2 chain drive. my Y plate is broken . do you sell just the Y plate or can I buy just the Y plate spec plan? I love this machine Its great. my name is Jeff Krug I bought the complete package and electronics from you guys. thanks

What electronics do you have at the moment? Depending on your machine, you will need a minimum of 3 stepper motors and 3 drivers (unless your heavy axis requires two stepper motors and two drivers). You will also need an interface board that is capable of providing three inputs for the THC (Torch Height Controller), THC on, THC up and THC down, and outputs for firing the torch. I would recommend the Pokeys57CNC interface for the primary interface. This interface will connect to the stepper motor drivers and the THC. The Pokeys57CNC can also communicate via USB or Ethernet.

Click the link to add information to this solution:
Looking for electronics for a plasmacam table. It's going to to be a 5'x10' table with x,y,z axis. Will be running on windows ten with a hypertherm powermax45 xp plasma cutter. Any information or links would be greatly appreciated!

The available options for the blackFoot, is only structural components with hardware, and structure components/hardware with electronic components.
However we currently do not have any plans available for public use/distribution.

Click the link to add information to this solution:
I have a 4x8 CNC and would like to cut my own parts for the Blackfoot. What is the price for the plans and the electronics ?

Yes, we offer a CNC electronics assembled package called the redFly, redLead and redSprout. If you already have a computer, I would recommend the redFly. You would still need to add connectors to the ends of your motor cable.

https://www.buildyourcnc.com/item/cnc-computer-system-redFly

Click the link to add information to this solution:
I need to replace the fried electronics box for my 6090 wood router. Do you offer a play and play, no wiring required, kit? If yes, how much? If no, can you recommend one?

if you purchased the USB interface, you will need planet-cnc software rather than Mach3, and you will need a usb cable to connect the usb interface to the computer.

The blackToe 2x4 CNC Machine Kit with optional table will need wire to connect the electronics. Don't forget to get some end mills to use for cutting the intended material.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
If I purchase the [blackToe 2x4 v4.1 CNC Machine Kit - USB Electronics - Table Included] all I would need for this CNC to be fully operational is a laptop with mach 3 software and a router. Is this correct?

Do you believe the source backlash is at the nut, or somewhere else?

Click the link to add information to this solution:
Hi Guys, I fitted new ball screws to my mill as part of a cnc conversion. I have about 0.15mm backlash in both the x and y axis. What would you recommend to remove the remainder of the backlash mechanically? Thanks in advance.

Yes, it is feasible to create a machine with a cutting area of 13'x15'. Your mechanical and structural systems will need to be able to span a bit more than the 13' if that will be the axis travel along the gantry.

We have not cut carpet with our lasers, but I don't see why not. With that said, be extremely careful with the materials in the rug. Read the MSDS (Material Safety Data Sheet) for the rug you intend to cut as some materials will emit corrosive and harmful gases and chemicals when lased.

Click the link to add information to this solution:
Hi I want to build a cnc laser table 13'x15' cuttting area. Is this feasible. Also would the 80watt laser be enough power to cut through carpet

We do offer all of the parts; but it is best to purchase them a la carte. You will probably not want the hardware since this would not conform to a design in metal.

All of the mechanical parts are available here:
https://buildyourcnc.com/CNCMachineMechanicalParts.aspx

All of the electronics you would need is available here:
https://buildyourcnc.com/electronicscombo.aspx

All of the laser components are available here:
https://buildyourcnc.com/LaserComponents.aspx

And the spindles and VFDs are available here:
https://buildyourcnc.com/SpindlesAndAccessories.aspx

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hello, I'm interested in GreenBull 5'x10' CNC machine kit with 40W laser head. Is it possible to receive an offer for this size cnc machine kit with all the mechanics, electronics and laser parts, but without all the wooden parts? We would like to build this kind of laser cutter machine with metal frame and parts. And is it possible also to get 3D drawing for machine? Waiting for your answer.

This version of the blueChick comes with the Parallel Breakout Board.

Click the link to add information to this solution:
Which electronics unit comes with item #230, the 3 axis USB or parallel? If parallel, do you have a package price that includes the USB electronics?